搜索资源列表
fhe-pulse
- 光电编码器采集脉冲的程序，采用计数查询等待中断方式， 液晶显示正反转 ,显示脉冲数（60个/转），显示转圈数-optical encoder pulse acquisition procedures adopted count inquiries pending interruption, LCD rotating direction Pulse a few shows (60 / switch), the show moved around a few
the
- 本系统的控制部分是以89C51为核心，采用集温度采集、A/D转化于一体数字温度传感器18B20作为温度处理部分。键盘控制接口采用键盘接口7279，通过其可以设定温度，设定PID算法的参数，并且可以设定当前时间，进行温度与时间显示的切换.采用数码管显示，可以实时显示实际温度。主电路是由光偶和晶闸管所组成的开关电路。控制电路通过PID算法，产生PWM波来控制主电路的通断，从而控制电炉的输出功率，达到温度控制的目的.-The system control part of the 89C51 as th
ADC
- philips ARM7 lpc2103 的AD口接光敏电阻，来探测LCD背光是否打开，并通过UART0，打印出AD转换后光米电阻测试的电压值，并输出LCD给光的开关状态-philips ARM7 lpc2103 I received the photo resistors AD to detect LCD backlight is turned on, and UART0, print optical AD conversion of the voltage meter to test the
Jgs
- 激光加工控制系统 可以读入plt文件，然后仿真，再通过并口 输出x y步进电机的驱动信号及开关光信号-Laser processing control system can read plt file, and then simulation, then through the parallel port output xy stepper motor drive signals and switch optical signals
MAN-switch-configuration-experience
- 在城域网交换机日常维护中经常会发现，一些申告有丢包、大延时甚至瞬间 中断的以太网专线接入故障中都是因为交换机端口设置不规范，将速率和双工模 式设成了自动协商，如果光电收发器和用户端口也都设置为这一状态，那么会导 致使用设置为10Mbps/100Mbps 自适应的光收发器和用户端网卡用户，实际接入 速率为全双工100Mbps，这样的话该用户的实际吞吐能力可达到200Mbps；另一 方面，因有些光收发器或用户端设备不具备自协商功能或被设置为10Mbps (100Mbps) 全
design
- 信令降频码方法的信令寻径式光纤交换机设计-Signaling down-code method of signaling routing optical switch design
SFPSerDes
- 光纤 收发器说明 光纤转RJ45 光纤4通道-Fiber Transceiver Descr iption 4-channel fiber optical switch RJ45
24-02-05
- Survivability in the Optical Internet Using the Optical Burst Switch. (Seunghun Oh, Younghan Kim, Myungsik Yoo, and Hyun Ha Hong)
sonant
- 基于光子晶体平板传导共振模的低功率光开关.-Based on photonic crystal flat-panel low-power conduction-mode resonant optical switch.
Large-mode-splitting-and-lasing-in-optimally-coup
- photonic crystal optical switch papers
CDROMControl
- 光驱开关控制程序，可以实现开关的控制，希望对大家有作用-Optical switch control procedures, can realize the switch control, and they hope to have everyone role
modena
- BCM5345 交换机程序C源码，千兆电口，光口程序-BCM5345 switch program C source code, Gigabit electrical interface, optical interface program
baluguangkaiguan
- 自己编的基于at89s52的8路光开关控制程序，含与上位机串口通讯部分，单片机通过232通信接受来自上位机的控制信号，并控制8路光开关切换。可以返回当前状态，并显示在小灯上。-Own series a at89s52 of 8-way optical switch control program, with part of the serial communication with the host computer the MCU through 232 communication accep
VCSOA_opticalswitch
- 这是一个关于基于VCSOA的光开关的仿真程序。仿真程序基于传输矩阵法设计的，将整个器件在轴向按折射率的不同分成很多层。计算了在外部抽运（即泵浦，加在放大器上的工作电流）呈现周期性变化时，放大器将输出一系列的光脉冲，即光开关。 - This is a simulation package for computing the characteristics of the VCSOA when acting as an optical switch, which is designed bas
ATtiny13-Optical-bistable-control--
- C程序-光控+声控双稳态.《单线进出电子开关》相关程序及资料-C program- Optical bistable control+ voice " singlet electronic switch out" the relevant procedures and information
CDROMControl
- 光驱开关控制程序.用VC++ 编写。控制光驱开和关。-Optical switch control procedures. Using VC++ to write. Control the drive on and off.
88E6095_88E6095F-8FE-P-3GE-
- marvell 8FE+3GE交换芯片设计手册,比较好的8光交换机方案芯片-marvell 8FE + 3GE switch chip design manual, better 8-chip optical switch program
SOFT
- ADUC812利用串口控制1*2光开关的端口选择，也可以通过手动控制光1*2开关端口选择-ADUC812 using serial port control 1* 2 optical switch port selection, can also be manually controlled light 1* 2 switch port selection
ZF_1X2
- 控制光开关设备的自动运行 测试光开关 数据-The optical switch control device automatically runs an optical switch test data
模块原理图
- 这是1X2磁光开光驱动模块图的子图，非常适合光电研发人员在设计光开关驱动时参考(This is the 1X2 magnetic optical switch driver module subgraphs, very suitable for reference in the design of R & D personnel photoelectric optical switch driver)