搜索资源列表
Stepper-motor-C-language-program
- 步进电机控制程序，正传，反转，加速，减速等，采用C语言编写-Stepper motor control procedures, Story, reverse, acceleration, deceleration, using C language
Stepper-motor-control-system-design
- 该设计中步进电机的驱动芯片采用ULN2003A，驱动程序写入AT89C52单片机中，通过程序控制步进电机的转速与转向。实现软件与硬件相结合的控制方法，使步进电机运行稳定、可靠性高，达到对步进电机的最佳控制。-The design of the stepper motor driver chip ULN2003A, the driver writes AT89C52 microcontroller, program control stepper motor speed and steering.
EXP28-stepper-motor
- 使用C8051单片机驱动步进电机 -Use C8051 singlechip driver stepper motor
Reversing-the-stepper-motor
- keil 51,单片机控制步进电机正转和反转。-KEIL, 51, stepper motor control of the positive rotation and the reverse rotation.
stepper-motor-control
- stepper motor control
51-single-chip-stepper-motor
- 基于MCS_51类型的单片机对步进电机控制的实现-MCS_51 type of single-chip stepper motor control based implementation
Stepper-Motor
- Stepper motor with AVR
Stepper-motor-speed-reduction
- 51单片机控制步进电机调速，51单片机进阶程序。-Stepper motor speed reduction
Stepper-motor
- 步进电机。51单片机实现步进电机的功能，好用 而且 适合初学者 。-Stepper motor
Stepper-motor
- 用单片机驱动ULN2003去控制步进电机，数码管旋转的角度会在数码管上进行显示。-MCU ULN2003 to drive stepper motor control, digital control rotation angle will be displayed on the digital pipe.
Stepper-motor-positioning.doc
- 一个关于步进电机定位控制系统VHDL程序与仿真的设计。-Design on a stepper motor positioning control system procedures and VHDL simulation.
Stepper-motor
- MSP430单片机编程 步进电机 状态机程序-MSP430 microcontroller programming stepper motor state machine program
Stepper-motor-speed-control
- 通过89C51单片机对电力行业控制器的研究，步进电机调速。-Controller of Power Industry，stepper motor speed control system.
Stepper-motor
- 步进电机控制程序 控制步进电机的正反转 加减速转动-Stepper motor control program control the step motor and reversing rotation acceleration and deceleration
Stepper-motor-speed-digital-display
- 本程序用于测试4相步进电机常规驱动 使用1-2相励磁 1-2相激励功率增倍，步进角度减半，抖动减少 顺序如下 a-ab-b-bc-c-cd-d-da 又称4相8拍 数码管显示 03-19速度等级，数字越大，速度越慢-This procedure is used to test the conventional 4-phase stepper motor driver
Four-phase-six-wire-stepper-motor
- 四相六线步进电机控制程序源代码，通过频率控制转速-Four-phase six-wire stepper motor control program source code, by frequency control speed
Stepper-motor
- Micro Processor .. PIC code for stepper motor-Micro Processor .. PIC code for stepper motor.............
Stepper-Motor-Controller-Using-C
- Stepper motor driver project with c programming source code
stepper-motor
- 步进电机为四相单四拍,8255输出步进电机驱动信号，电机线圈A、B、C、D四相由8255的PC口PC0-PC3控制，逆时针：D→DC→C→CB→B→BA→A→AD→D→…,顺时针：DA→A→AB→B→BC→C→CD→D→DA→… 键盘0~9控制转速，B或C控制方向，F退出 数码管显示S.SPEED- i，i为转速-Four-phase stepper motor is a single four-beat, 8255 stepper motor drive output signal,
10-Stepper-motor
- 步进电机的控制,keil C编程,初学者的福音-Stepper motor control