搜索资源列表
rob_stm32.tar
- stm32,机器人控制代码,直流减速电机,舵机,超声波模块,串口通信-stm32, robot control code, DC gear motors, servos, ultrasonic module, serial communication
BLDC_NS
- 本文件是关于直流无刷电机的控制完整程序,花费了我两个月的时间来完成!-The fire is the control of BLDC based on STM32. It takes my two mouths to finished this program.
BLDC
- STM32采用TIM1的PWM输出,控制直流无刷电机 上传一个基本初级版的程序 PA8 PA9 PA10 PB13 PB14 PB15是PWM输出口 PC5接个电位器调节速度 PB12电源指示灯 PB5正转指示 PB2反转指示 PB0按键开机 PB1按键正反转 宏定义DEBUG可以软件仿真(DEBUG用来开启相关变量,以及变换霍尔相序)-Finally realized TIM1 PWM output, brushless DC motor control
bldc
- 平衡车控制之BLDC直流无刷电机控制 基于STM32,死区控制,倾角补偿-BLDC for STM32 Driver
bujindianjikongzhi
- 基于stm32的直流步进电机控制程序,可以通过编码器进行控制-Based stm32 DC stepper motor control procedures can be controlled by an encoder
BLDC_HALL
- 基于STM32的直流无刷电机控制程序,带霍尔传感器-Brushless DC motor control procedures
Motor_Control
- 基于STM32的直流无刷电机控制,包含调速功能,且各个功能函数已经封装好-Brushless DC motor control based STM32, including speed control function, and the function of each function has a good package
STM32F103_BLDC
- STM32 进行BLDC的电机控制,BLDC又称直流永磁电机,或永磁同步电机-STM32 BLDC
stepsensor
- 直流电机编码器检测驱动,适用于STM32,单片机,嵌入式- 28/5000 DC motor encoder detection driver for STM32, single-chip, embedded
test-mini
- 这是STM32 Mini板的智能风扇的程序,利用DS18B20作为温度传感器,L298N驱动直流电机实现风扇智能调速-This is the STM32 Mini board intelligent fan program, the use of DS18B20 as a temperature sensor, L298N drive DC motor to achieve intelligent fan speed
BLDC_HALL
- 运用Keil编程环境,使用STM32 语言进行编程,使用的是STM32芯片,无刷直流电机的位置信号的输入。-Using the Keil programming environment, the use of STM32 language programming, the use of STM32 chip, brushless DC motor position signal input.
PID-Tuning-deviceV2.0
- STM32 PID算法调节直流电机来控制调节需要达到的380V交流电的电流值采用PID算法+pwm来调节需要达到的电流值-STM32 PID algorithm to adjust the DC motor to control the need to achieve the adjustment of the 380V AC current value using the PID algorithm+ pwm to adjust the required current value
BLDC-TEST-stm32
- 基于stm32的直流无刷电机源码,按键调速,非常好用-Brushless DC motor based on STM32 source code
双轮平衡车程序
- stm32设计的平衡车,用于驱动直流电机,实现平衡车的控制(STM32 designed balance car)
MiniBalanceV3.5【大功率版】平衡小车源码
- 本系统为两轮自平衡小车系统,由STM32单片机控制模块,陀螺仪姿态检测模块,电机驱动模块,电源供电模块等组成。陀螺仪MPU-6050模块负责采集平衡小车的角度信号以及角速度信号,并传给单片机;STM32单片机控制模块处理姿态角数据后,通过PID算法调节电机驱动电压,以控制两轮小车达到平衡;电机驱动模块负责接收单片机输出的控制信号,驱动两个直流电机的转速和方向,编码器将电机的速度和方向反馈给单片机控制器;电源模块负责各个模块的供电。通过系统的硬件软件设计、测试,证明了两轮自平衡小车能在±5 °范围
自平衡小车
- 两轮自平衡小车,stm32103,直流无刷电机(Two wheel self balancing vehicle, STM32103, DC brushless motor)
BLDC_HALL
- stm32用于控制直流无刷电机,实现了电机的稳定运行和保护(Stm32 is used to control a brushless DC motor which runs very stable)
BLDC PMSM2 HALL - 1 -1
- 基于STM32的BLDC矢量控制程序,以STM32为MCU搭建系统,可实现对直流无刷电机的FOC控制与PWM控制(BLDC vector control program based on STM32, with STM32 as MCU to build the system, can realize the brushless DC motor FOC control and PWM control)
STM32F407 Ethercat
- 直流有刷电机驱动程序,基于STM32F4(DC brush Motor Driver code, based on STM32F4)
embedded
- 本系统中使用了STM32F103VET6核心板、温度传感器DS18B20、lcd12864(串行)、直流电机模块、独立按键模块、蜂鸣器模块,模拟家用热水器的工作过程。除检测温度外,该系统在温度低于设定温度(系统初始设置50摄氏度)时电机旋转并且温度越低转速越快、核心板上的小灯按照特定规律(先由led0到led15逐个点亮再反向逐个熄灭再正向单个点亮)点亮;温度低于20度时增加蜂鸣器报警功能;独立按键可以调节用户设定温度大小。(A water heater system based on STM3