搜索资源列表
8051F330 pid ad 舵机模拟串口数码显示
- 8051F330 pid\ ad\舵机\模拟串口\数码显示,8051F330 pid\ ad\servo \sci\dispaly
SOFT-UART
- 51 单片机io口模拟串口程序,带中文说明。-soft UART
chuankou
- I/O口模拟串口(利用中断,波特率可达115200以上)-I/O serial port simulation (using interrupted, baud rate up to more than 115,200)
CommMonitor
- CommMonitor 侦测、拦截、逆向分析串口通信协议, 是侦测RS232/422/485串行端口 的专业工具软件,是软硬件工程师的最佳助手。CommMonitor 能侦听、拦截、记录、分析 串行通信协议,让您对应用程序操作串行端口的过程和细节,让您及时的模拟被侦听程序 或设备的数据、控制流,提高工作效率。 -CommMonitor detection, interception, reverse analysis of serial communication protoco
DS1302
- 时钟程序,大家是否想到用定时器,对,也可用定时器的中断来处理,这样的程序我想不用我说了吧! 你们可自己发辉下,本程序采用外元件DS1302时钟IC,使用此IC不增加系统资源,要时钟时直接去读取就可以了 本IC跟ADC0831一样以串口方式传送数据,不同的是协议,只要你读懂它的串口协议,就可以用P口来模拟协议进行 ,这样更能使你对传送数据协议的了解,在看本程序之前,先看看芯片的串口协议 -Clock process, whether you think using the time
UART_VHDL_Verilog_Lattice
- 本压缩包中含有串口程序的VHDL,Verilog,Lattice三种版本的代码,均已实现。在压缩包中,含有非常详细的串口的实现规格。各种版本的代码中,含有完成的源文件,测试文件,模拟文件。-This compressed package contains serial process VHDL, Verilog, Lattice three versions of the code, have been achieved. In the compressed package, contains
serial_Simulation
- 单片机IO口模拟串口(接收+发送) 环境:STC单片机+KEIL2 使用单片机的IO口模拟串口。其中分别包含模拟串口接收数据和模拟串口发送数据两个测试程序。 另外,程序附加说明中对网上流传的一个不错的模拟串口代码提了一些改进建议,并说明了测试程序应用于实际工程需要注意的几个地方。-Simulation of Single-chip Serial IO port (receive+ send) Environment: STC Single-chip MCU+ KEIL2 use an
SERIAL
- vc串口通讯完整源码,模拟超级终端,是串口编程的良好实例-vc serial comunication code
IO
- 大家好!我为大家提供个小程序,单片机汇编语言编写的IO模拟串口程序,此程序可供参考和使用-Good! I provide a small program, single-chip assembly language prepared by serial IO simulation procedure, this procedure can be used as reference and use
COMMON_FS_MS
- ATMEL arm7 USB 模拟串口-ATMEL arm7 USB analog serial
UART
- 单串口8051内核单片机模拟双串口程序源代码-8051 single-core single-chip serial analog dual serial source code
iouart
- 模拟串口的通讯程序,采用的AVR单片机进行编程,C语言编写的-Simulation of serial communication procedures used in single-chip AVR programming, C language
USART_SIMc
- 模拟串口通讯,用于I0口不足是可扩展通讯-Simulation of serial communication, for mouth I0 is the lack of scalable communications
51
- 51单片机模拟串口的三种方法,简单易用,可满足双机通讯-err
msp430f149monichuanku
- 这是在TI网站上下的例程,绝对可用, P2.2,p2.3,在示波器上调试,调BitTime可以调节脉冲宽度,就可以调节波特率了,模拟串口发送一个字节需要发10位,起始位+8位有效数据+停止位,二真实串口不用发起始和停止位,因为缓冲区已经将他们加上了-This is a site from top to bottom in TI routines, absolutely available, P2.2, p2.3, in oscilloscope debug, tune BitTime can
IO_RS232_String
- 模拟串口传输字符串,可以传输4个字节的数据,可以修改数组长来确定传输大小。-Simulation of serial transmission string, you can transfer 4 bytes of data, can modify the number of head to determine the transmission size.
555
- 11.3.1 基于CAN总线的模拟量输入 VB 串口编程-11.3.1 Based on CAN Bus Analog Input serial programming VB
COM
- Keilc51编写的51单片机模拟串口程序-Keilc51 prepared by 51 serial single-chip simulation procedures
mutibyte_scom
- PIC单片机16f628A串口发送接收程序.汇编语言编写-PIC single-chip serial port to send procedures. Compiled languages
serial
- 单片机模拟串口通讯 I/O口模拟232通讯程序 使用两种方式的C程序 占用定时器0-Analog single-chip serial communication I/O port 232 Analog communication procedures in two ways to use the C program occupied timer 0