搜索资源列表
C-for-Uart-programs
- C语言编写的异步串行通信接口程序 非常实用的哦-C language program asynchronous serial communication interface
URAT
- 串行通信接口UART设计,串行通信接口是指将构成字符的每个二进制数据位,依据一定的顺序传送的通信方法。-UART serial communication interface design, serial communication interface refers to the form of binary data bits per character, based on a certain order to send the communication method.
EXAMPLE4.15
- PIC16887A单片机一个双机通信,2个单片机异步串行通信接口相连方式为:RX和TX交叉对接,左边的单片机U1,每按下按键S1就发送一个字节数,从0x20开始发送,每送一个数据,此数加1.发送的同时在D口上输出。右边单片机U2为接收状态,采用中断方式,如有接收中断,则进入中断,将接收到的数直接在D口上输出-PIC16887A a two-machine communications microcontroller, two asynchronous serial communication i
SCIB
- DSP2812入门程序: 串行通信接口SCIB应用之普通串口-DSP2812 entry procedures: application of a serial communication interface SCIB ordinary serial
BA2yupYr
- RS232C串行通信接口的应用,也许你能看到这上面有一块51单片机,并且该电路连接到电脑上-RS232C serial communication interface application, perhaps you can see above there is a 51 single, and the circuit connected to the computer
gs
- 串行通信接口的应用,用于连接单片机,并且该电路连接到电脑上-RS232C serial communication interface application, perhaps you can see above there is a 51 single, and the circuit connected to the computer
sci.c
- F2812 EVM板上扩展标准 RS-232 串行通信接口实验-F2812 EVM board to expand the standard RS-232 serial communication interface experiment
async_transmitter
- RS232。串行通信接口RS232,verilog -failed to translate
FPGA-and-cpu
- FPGA与单片机的串行通信接口的程序设计-FPGA and cpu
Voice-chip
- ISD4004 系列工作电压3V,单片录放时间8 至16 分钟,音质好,适用于移动电话及其他便携式电子产品中。芯片采用CMOS 技术,内含振荡器、防混淆滤波器、平滑滤波器、音频放大器、自动静噪及高密度多电平闪烁存贮陈列。芯片设计是基于所有操作必须由微控制器控制,操作命令可通过串行通信接口(SPI 或Microwire)送入。-The ISD4004 series voltage is 3V, the monolithic recording time to 16 minutes, good so
msp430x41x
- 低电源电压范围为1.8 V至3.6 V 超低功耗: - 主动模式:280μA,在1 MHz,2.2伏 - 待机模式:1.1μA - 关闭模式(RAM保持):0.1μA 五省电模式 欠待机模式唤醒 超过6微秒 16位RISC架构, 125 ns指令周期时间 12位A/ D转换器具有内部 参考,采样和保持,并 AutoScan功能 16位Timer_B随着三† 或七‡ 捕捉/比较随着阴影寄存器 具有三个16位定时
AVR-MCU-development
- 利用ATmega16单片机实现对电压值的采样,经芯片内部AD转换,再调用程序将AD转换值转换为实际电压值,并用数码管显示。再由串行通信接口将数据传送到PC机显示,并用2个键控制采样速度。附带原理图,编程代码。-Use ATmega16 microcomputer for voltage sampling, the chip AD conversion, then convert a AD value to the actual voltage values and display on digi
dsp
- 第1章DSP2407概述,第2章系统配置和中断,第3章存储器和IO空间,第4章时钟和低功耗模式,第5章数字输入输出,第6章事件管理器,第7章模数转换ADC模块,第8章串行通信接口SCI ,第9章串行外设接口SPI,第10章CAN接口,第11章看门狗,第12章开发工具及开发环境,第13章程序设计-Chapter 2 System Configuration and interrupt Overview Chapter 1 DSP2407, memory and IO space on Chapte
ISD4004
- ISD4004 系列单片语音录放 内置串行通信接口,可实现8到16分钟,8KHz采样率语音录放。工程文件为Keil C51。51单片机试验模块。-The ISD4004 series monolithic voice recorder built-in serial communication interface, can achieve 8-16 minutes 8KHz sampling rate voice recording. Engineering a microcontrolle
LX-2011-28PIN-UART
- 该例子简单实现了PIC18F2550单片机的串行通信接口(UART)的接收和发送功能。-The example of simple the PIC18F2550 microcontroller serial communication interface (UART) receive and transmit functions.
SCI_RS232
- 串行通信接口可以用RS-232来实现同外设发送和接受数据信息。-Serial communication interface RS-232 to achieve the same peripherals to send and receive data information.
Microcomputer-principle.rtf
- 存储器(RAM 6264)扩展 可编程并行接口(8255)扩展 可编程计数/定时器(8253)扩展 A/D、D/A转换 可编程串行通信接口(8251)扩展 -Memory (RAM 6264) extended programmable parallel interface (8255) extended the programmable counter/timer (8253) Expansion A/D, D/A conversion programmable seri
uart
- VHDL编写的UART异步串行通信接口程序,,,经过仿真验证,简单易懂-VHDL prepared UART asynchronous serial communication interface program, through simulation, simple,,,,,
SCIB
- 基于DSPTMS320F2812的串行通信接口SCIB应用之普通串口代码-Serial communication interface based DSPTMS320F2812 ordinary serial code SCIB application
UART
- STM320F2812 DSP 串行通信接口SCIB应用之普通串口-Ordinary serial STM320F2812 DSP application of the serial communication interface SCIB