搜索资源列表
taxi
- 出租车计费器,用以实现出租车计费的小程序,用VHDL编程实现-Taxi meter, used to achieve a small taxi billing procedures, using VHDL programming
chuzhuchejifeiqi
- 利用FPGA芯片控制出租车计费系统,采用Verilog HDL编写,程序简介-Control the use of FPGA chip Taxi billing system, using Verilog HDL preparation, procedures for
yunlei
- 实现出租车计费系统,包含所有的源文件-Taxi billing system to achieve
jifei
- 在Quartus环境中,采用VHDL语言编写的出租车计费系统,系统共分为分频、状态切换、记程、计费等模块,模仿现实中出租车计费。-In the Quartus environment, the use of VHDL language taxi billing system, the system is divided into sub-frequency, state switching, recording process, billing and other modules, to imi
taxibillingsystem
- VHDL语言设计的出租车计费系统,在老师的指导下完成的,并在实验箱上测试通过。-VHDL language design taxi billing system, completed under the guidance of their teachers, and the experiment on the test box.
YUZHI
- 出租车计费器,能实现车费、车程显示,单价、起步价设置。-Taxi meter, can achieve fares, car shows, unit prices starting to set.
anjian
- 基于单片机的出租车计费系统,可以设定单价以及等待时间计费等功能-Taxi billing system based on single chip, you can set the unit price and the wait time billing and other functions
taxi
- 出租车计费系统,用c51单片机,c语言,非常好的,运行通过,功能也达到要求。-Taxi billing system, with c51 microcontroller, c language, very good, running through, and feature meet the requirements.
Taxi_meter
- 设计一个满足日常生活所需功能的出租车计费器,实现计费功能。-Designed to meet the daily needs of a taxi meter function and achieve billing functions.
taxi
- 基于FPGA的出租车计费器 所要设计的出租车计价器,要求能够显示里程数和乘客应付的费用,其中里程数精确到0.1km,乘客应付的费用精确到O.1元,显示必须以十进制的形式来进行。出租车的计费标准为:起步价6元,里程在3 km以内均为起步价;里程在3~7 km之间时,每行驶1 km增加1.6元;超过7 km时,每行驶1 km增加2.4元。-FPGA-based taxi meter by meter taxi to design, requires the ability to show mi
TaxiMeterProgramToAchieveFunctional
- 出租车计费器程序,能实现功能。包含存储各种价格,里程计算,各种模式的切换。程序流程图思路清晰。-Taxi meter program to achieve functional. Includes storage of various price, mileage calculation, the various modes of switching. Flowchart of clear thinking.
22222
- 出租车计费器 可以记录汽车行程从而算出所需要的路费-Taxi meter can record car trips to work out the required toll
chuzuche5
- 本程序详细的描述了出租车计费器,可直接应用。-This procedure is detailed procedures for the taxi meter can be directly applied.
eda
- 该系统利用VHDL语言、PLD设计出租车计费系统,以MAX+PLUSⅡ软件作为开发平台,设计了出租车计费器系统程序并进行了程序仿真。使其实现计费以及预置和模拟汽车启动、停止、暂停等功能,并动态扫描显示车费数目。-The system uses VHDL language, PLD design taxi billing system to MAX+ PLUS Ⅱ software as a development platform, the taxi meter system was desi
TAXI
- 基于VHDL的出租车计费器,通过VHDL语言来编程实现计费系统的四个功能块:分频模块,控制模块,计量模块和译码显示模块,最后使用MAX+PLUSII软件来对程序进行仿真,以模拟实现出租车的启动,停止以及等待等过程中的计时,计程和计费功能。-Taxi meter based on VHDL, VHDL language programming through the billing system of the four functional blocks: frequency module, co
taxicounter
- 出租车计费器能实现计费功能,三位数码管显示。起步费为6元-taxi counter
EDAsheji-chuzuche-jifei
- 设计一个出租车计费器,能按路程计费,具体要求如下: (1)实现计费功能,计费标准为:按行驶里程计费,起步价为6.00元,并在汽车行驶2km后按1.2元/km计费,当里程数达到15km后,没千米加收50 的空驶费,车辆停止和暂停时不计费。 (2)现场模拟汽车的启动、停止、暂停和换挡等状态。 (3)设计数码管显示电路,将车费和路程显示出来,各有1位小数。 -Design of a taxi meter, to the journey billing, specific require
出租车
- 可以实现计费功能,与距离。已经仿真过可以使用(Billing function and distance can be realized.It has been simulated and can be used)
出租车计费器设计
- 实现出租车计费功能,可以在数码管上显示里程及费用(To realize taxi billing function, it can show mileage and cost)
chuzujifei
- 使用Quartus II 9.0编写的出租车计费系统源码,是课程设计大作业验证通过,可以直接仿真验证(The use of Quartus II 9 written taxis charging system source code, is the course design of large work verification through, can be directly simulated and verified)