搜索资源列表
AD0809
- ADC0809做的数字电压表，0-5V，4个LED直接接单片机做显示，动态扫描写的驱动-ADC0809 do the figures in Table 0-6 voltage - 5V, 4 LED SCM done directly, dynamic scan was driven
tqbysj
- 基于单片机的数字电压表 和 跑马灯的切换程序-based SCM digital voltage meter and 5,250 of the switching process
WL024_ADC0832数字电压表LED显示
- 控制ADC0832做数据采集，并用数码管显示出来，搞测控的朋友可以-control data acquisition, control and digital display and control of engaging friends can play
dyb
- 利用单片机AT89S51与ADC0809设计一个数字电压表，能够测量0－5V之间的直流电压值，四位数码显示，但要求使用的元器件数目最少-SCM AT89S51 ADC0809 design with a digital voltmeter to measure 0 - 5V DC voltage between the value of four digital display, but requires a minimum number of components
data_vol_counter
- 数字电压表 利用单片机AT89S51与ADC0809设计一个数字电压表，能够测量0－5V之间的直流电压值，四位数码显示，但要求使用的元器件数目最少。 -digital voltmeter SCM AT89S51 ADC0809 design with a digital voltmeter, capable of measuring 0 - 5V DC voltage between the value of four digital display, but requires
AD_ASM_AD0832shuzidianyabiaoLED
- 数字电压表 AD芯片： 采用8位串行A/D转换器ADC0832。 ● 8位分辨率，逐次逼近型，基准电压为 5V ● 5V单电源供电 ● 输入模拟信号电压范围为 0～5V ● 有两个可供选择的模拟输入通道 显示： 使用三个数码管。 显示范围： 0.00 － 5.10 （单位：V） 连接方式： AD_CLK → P1.0 AD_DAT → P1.1 AD_CS → P3.4 模拟输入 → CH0
shuzidianyabiao
- 基于单片机系统的8路数字电压表程序设计问题-SCM system based on eight-way digital voltage meter design procedures
P-v-dianyabiao
- PC数字电压表的设计,原理图以及代码,设计文档.此数字电压表的优势在于可以通过串口将测量所得到的电压值传给PC机,这样的话有利用整个数据的采集与分析.上位机采取的是串口通信软件.-PC digital voltage meter design, diagram and code, Design Documentation. This figure voltage meter advantage is through the serial port will be measured by the
shuzidianyabiao1
- 一个很好的数字电压表的源程序～～～～～～～值得大家参考。-a good digital voltage of the source ~~~~~~~ valuable reference.
ex6-2
- 用KEIL C编写的数字电压表，比较使用且经典，欢迎大家喜欢，共享-KEIL C with the preparation of digital voltage meter, compared with the use of classic, welcoming everyone likes to share
lcd_v
- 使用凌阳单片机制作的一个数字电压表,直接采用凌阳自带的AD转换,通过LCD显示转换结果.-use of a microcontroller production figures voltage meter, Sunplus, bringing their direct use of AD conversion, LCD Display through conversion results.
vdevice
- 基于FPGA系统的数字电压表设计大范围，超精确的详细报告，共有40多页-FPGA-based system design digital voltage meter large-scale and ultra-precise details of the report, a total of over 40 pages
digitalvolge
- 单片机应用实例之一：基于单片机的数字电压表-one example : SCM - based Digital Voltmeter
shzdyb
- 这是在FPGA上实现的数字电压表，用VHDL编写的，已通过编译，仿真验证。-This is the FPGA to achieve the digital voltage meter, prepared by using VHDL, compile and simulation.
VOLTE2
- 简易数字电压表的设计2 利用单片机AT89S51与ADC0809设计一个数字电压表，能够测量0－5V之间的直流电压值，四位数码显示，但要求使用的元器件数目最少。-simple digital voltage meter design AT89S51 2 microprocessor design with a few Connection between ADC 0809 word voltage meter, capable of measuring 0 - 5V DC voltage b
ADC0832-1602LCD
- 这是一个062-AD0832数字电压表1602液晶，适合初学者及工程开发。-This is a 062 - AD0832 digital voltmeter 1602 LCD, for beginners and project development.
Volt-Ampere
- 数字AVR电压表和电流表项目：这是一个ATmega8的微控制器的数字电压表测量电压0.0-40.0伏与0.1伏的分辨率。 furtheremore有两个在这个项目上的最小和最大的继电器。您必须为电流表并联一个1欧姆，5瓦的电阻这个项目。-Digital AVR Voltmeter and Amperemeter Project: This is a digital voltmeter by ATmega8 microcontroller that measure voltage 0.0-40
ADC0832
- 本程序为数字电压表输入电压经89k电阻和10k精密电位器分压测试电压为0～51v，可用表校对-The procedure for the digital voltmeter input voltage and 10k by 89k resistor divider test precision potentiometer voltage 0 ~ 51v, proof of available tables
TLC2543 protues仿真
- 通过TLC2543采集到的电压送到数码管显示，程序调试好，含protues仿真。(The voltage collected through the TLC2543 is sent to the digital tube display, the program is debugged well, and the Protues simulation is included.)
实验7 直流数字电压表设计
- 在编程软件配合下，要求实现如下功能：调解电位器RV1可使其输出电压在0~5V之间变化。经A/D转换后，数码管以十进制数形式动态显示电位器的调解电压。(In cooperation with the programming software, it is required to realize the following functions: The adjustment potentiometer RV1 can change its output voltage between 0~5V. A