搜索资源列表
驱动led显示
- //串行驱动led显示, //一个74hc595位移寄存器驱动三极管驱动led位, //两个74hc595驱动led段,方式位5位x8段x2=10个数码管 //5分频,每次扫描时间位1.25ms //定义特殊符号-/ / Serial Driver led, / / a 74hc595 displacement register drives the triode-led drive, / / 2 74hc595 led drive, five-way x8 of x2 = 10 digital
szz0001
- 用VHDL语言写的一个8位动态扫描显示的时钟程序,数码管的片选须接一个3-8译码器。-VHDL83-8
stepper_motor_controller
- 步进电机控制程序,用51单片机控制步进电机的运转,可实现电机的正转、反转、归零、自动速度调解,4x4键盘扫描输入需要电机转动的相位,6为数码管显示当前的角度等功能。单片机程序用C51编写。-stepper motor control procedures, with 51 MCU control of the stepper motor operation, the motor is transferred, inversion, zeroing, automatic speed mediati
7segment
- 这个是max plus2的7段数码管的扫描程序。文件格式为hif,介绍7段数码管的设计方法。 你好,管理员,我十分需要贵网站的一个程序,请为我开通下载。我会尽力上传源码,支持网站的发展。-this is the max plus2 7 of the tube digital scanning procedures. Hif document format, introduced seven of the digital control design methods. Hello, admin
saomiaoxianshi
- 这是s52的扫描显示程序,4个数码管,可显示4位不同的数字,通过按键改变数字的大小,适于51单片机初学者学习
test
- 基于FPGA的数字秒表(数码管扫描)程序。 平台:quartusII 15.0-FPGA-based digital stopwatch (digital scan) program. Platform: quartusII 15.0
calculator-for-51
- 基于AT89C51RC单片机的科学计算器,采用8位数码管扫描显示,矩阵键盘采用反转法扫描,效率更高,速度更快。-Based on the AT89C51RC microcontroller scientific calculator, the use of 8 digital tube scanning display, matrix keyboard using reverse scanning method, the efficiency is higher, faster.
dianzhen
- 需要实现点阵按列依次并且循环显示的效果,可以分析视觉上可以观察到列的变化,则列的扫描频率必定要远远小于行扫描的频率。在程序中,设置行扫描的频率等于前次实验中数码管扫描的频率,设置列扫描的频率为5HZ,即每0.2s显示亮的一列向前推进一列。在程序中,使用16进制计数作为74HC154的输入:分出5hz的频率,并用其计数,将计数值作为74HC154,则其译码产生的输出变化也为5hz,并且实现每列一次选通。由于每行对应的数码管共阳极。直接赋高电平。则可以实现所需要的功能。行扫面则是要实现先依行点亮,
main
- 数码管扫描显示程序,这个程序本人亲写,有不当的地方,欢迎大家来指教-Scanning digital tube display program, the program I write, there is improper, welcome everybody to give advice or comments
display_sm
- 数码管扫描verilog源代码 display code verilog-display code
lab3
- 数码管扫描电路,通过扫描数码管实现多个数码管同时显像功能-Digital scanning circuit, through digital scanning of multiple simultaneous digital imaging capabilities
Digital-tube-display
- 一种用VHDL写的数码管扫描电路,简单明了,仅供参考-One kind with VHDL written digital scanning circuit, plain and simple, for reference only
2014011494
- FPGA嵌入式开发全加法器程序。二进制运算器及数码管扫描电路-FPGA embedded development full adder program. Binary calculator and digital tube scanning circuit
saomiao
- 89c51巴顿数码管循环显示2017可能有点不兼容(Digital tube cycle display 2017)
51单片机按键扫描程序
- 51单片机加外设,利用实验板提供的键盘扫描电路和显示电路,做一个扫描键盘和数码显示实验,把按键输入的键码在六位数码管上显示出来。(51 SCM plus peripherals, the use of the experimental board keyboard scanning circuit and display circuit, do a scan keyboard and digital display experiment, the key input code in six di
shumaguan
- 用于数字码与扫描显示数码的解算 可修改运算过程来适配所需要的输入数据格式(It can be used to modify the operation process of digital code and scanning digital display to adapt the input data format)
3
- 设计一个键盘接口电路。要求: (1)用200Hz时钟频率有效地去除按键的抖动; (2)用20Hz时钟频率对键盘进行扫描识别,并用数码管将按键的编号显示出来;(Design a keyboard interface circuit. Requirements: (1) use the 200Hz clock frequency to effectively remove the shaking of the keys; (2) scan the keyboard with 20Hz clo
saomiaojianpan
- 用于扫描矩阵键盘,并将扫描到的键盘值用数码管显示(Used to scan the matrix keyboard and display the scanned keyboard value with a digital tube)
4乘4键盘扫描控制器
- 1. 键值采用16进制编码,即16个按键分别对应显示16进制数 0~F,按键对应关系如下:最上面一行从左至右依次为0~3, 第二行从左至右依次为4~7,第三行从左至右依次为8~B,最 下面一行从左至右依次为C~F,其中b、d显示为小写,其他字 母大写; 2. 按键按下时显示当前键值并保持,直到下一按键被按下时更新 显示; 3. 只有按键被按下时蜂鸣器发出按键音,放开后蜂鸣器不发声。 4. 每个按键对应不同的按键音。(1. The key value is encoded in hexadecim
键盘扫描
- 用AT89S51的并行口P1接4×4矩阵键盘,以P1.0-P1.3作输入线,以P1.4-P1.7作输出线;在数码管上显示每个按键的“0-F”序号。