搜索资源列表
PWM-motor
- 采用51单片机PWM方式控制直流电机转速,闭环系统,转速采用数码管显示,采用PROTEUS仿真-With 51 single-chip PWM control of DC motor speed, closed-loop system, the use of digital speed display, using PROTEUS simulation
DS18B20-atmega128
- DS18B20 测试温度并在数码管上显示-DS18B20 test temperature and digital display
verilog
- verilog实现的数字频率计8位数码管输出显示同时矩形波分档输出-verilog implementation of digital frequency meter
DS1302
- DS1302配合数码管显示,可通过按键进行设时!-DS1302 with digital display, can be carried out through the buttons located at!
displaydaly
- 这个是显示的子程序,可以使用他在数码管上显示.-this is an indication that the subroutine, he can use the digital control on the show.
at89s52_clock_time
- 这个是个4个数码管显示时间的程序,用AT89S52实现,用四个按键控制,能实现时钟显示,闹钟定时,倒计时三项功能,电路图很简单。-This is a 4 digital tube display time-consuming procedures, use AT89S52 realize, with four buttons control, can realize the clock display, alarm clock, timer, countdown to the three fun
DS18B20
- 利用89S51单片机,通过DS18B20温度传感器测得当前的温度值,再送入4位8段数码管显示-Using 89S51 microcontroller, temperature sensor, through DS18B20 measured current temperature value, and then into four 8 digital tube display
485Mon
- 这是一段简单的8位数码管驱动程序,解决单片机菜鸟们的单片机入门苦恼,纯源码-This is a simple 8-bit digital tube driver to resolve the single-chip microcontroller菜鸟们entry distress, pure source
freq
- 智能频率计 1. 频率测量范围为1Hz~1MHz 2. 当频率在1KHz以下时采用测周方法 其它情 况采用测频方法.二者之间自动转换 3. 测量结果显示在数码管上,单位可以是Hz(H)、 KHz(AH)或MHz(BH)。 4. 测量过程不显示数据,待测量结果结束后,直接显示结果。 -Intelligent frequency meter 1. Frequency measurement range of 1Hz ~ 1MHz 2. When th
seg_key
- 51单片机按键控制数码管显示程序,显示为时钟倒计时,有暂停和计数功能-51 single-chip digital tube display key control procedures, shown as the countdown clock, a pause, and count functions
dianzizhong
- 定时器0中断, 用于数码管的动态扫描 定时器1中断, 用于产生0.01s的时钟-Timer 0 interrupt, for digital control of dynamic scanning timer 1 interrupt, used to generate clock 0.01s
LedCtrlUse
- 实现浮点数的LED显示,模拟七段数码管显示数字及小数点,里面还包含数字键输入功能.-The realization of floating-point numbers of the LED display, analog Seven-Segment LED display figures and the decimal point, which also includes a numeric keypad input capabilities.
scan_led
- 一个8位数码管扫描程序,经过编译和仿真.-An 8-bit digital tube scanner, after the compiler and simulation.
shumaguan
- 关于51单片机开发板的数码管显示程序 本人菜鸟 望大家多多指教-51 MCU development board on the digital tube display program I hope everyone rookie exhibitions
stc232
- 1.通过PC端的串口调试工具,从PC端发出一个十六进制的数, 通过串口传输到单片机,并有单片机通过LED数码管显示其ASII码,而且单片机又将这个数发回PC端,并在PC端显示出来,从而实现单片机与PC机的通讯 2.可以实现对下位机数据实时采集(如温度,程序中设定的是37摄氏度) 3.可以控制流水灯或继电器开关等-1. Through the PC-side debugging tools for serial port, from the PC client sends a hexa
dongtai
- 这是一个数码管动态显示的C语言程序.适合初学单片机朋友参考使用.-This is a dynamic display of digital tube C language program. Singlechip friends for beginner use and reference.
dongtai1
- 这是另一个数码管动态显示的C语言程序.请有兴趣的朋友参考参考.-This is another dynamic display of digital tube C language program. Interested parties are invited to refer to refer to a friend.
clock
- set(key6) left(key5) right(key4) up(key3) down(key2) OK(key1) 功能一:时钟 时钟计时; 按下set(一次)键即可调时间,此时时钟计时停止,按left,right左右移动点,移动到需调的的数码管, 按up,down进行数字的调节,按OK键保存退出。 功能二:整点报时和闹钟 当时钟走到整时时,报时滴滴响四次; 按set(二次)键进入调节闹钟,此时时钟继续走动,按left,rig
DS18B20
- 温度传感器18B20程序,本设计硬件简单,用4位数码管显示-Temperature sensor 18B20 procedure, the design of the hardware is simple, with four digital tube display
18B20
- DS18B20温度控制数码管 1、K3 → 进入设定温度报警值 TL 状态:L--20 2、K3 → 进入设定温度报警值 TH 状态:H--28 3、K3 → 返回-DS18B20 temperature control digital tube 1, K3 → to enter the set temperature alarm value TL state: L- 20 2, K3 → to enter the set temperature alarm value TH stat