搜索资源列表
SD_
- SD模拟一个串口,SPI进行读写功能,附带原理图,很实用的,方便直接调用。-SD simulate a serial, SPI read and write functions, with schematics, very practical, convenient and direct calls.
a
- 可以再串口仿真模拟软件实现,可以解决一些实习作业之类的事情-i can
430AD
- 将ADC对P6.0端口电压的转换结果按转换数据和对应的模拟电压的形式通过串口发送到PC机屏幕上显示-ADC conversion results will be displayed on the P6.0 port voltage and the corresponding data in the form to convert the analog voltage is sent to the PC via the serial port on the screen
89c52
- 单片机程序: 液晶显示距离(需选配超声波探头) 电机速度测试程序 (需选配测速模块) 喇叭音量调节 舵机按键控制程序 点阵模拟电梯上行下行 串口通讯中断应用12M晶振 波特率2400 串口测温电脑显示 DS1302时钟串口自动更新时间 12M 波特率2400 1602液晶4位数据静态显示-SCM procedures: LCD distance (with optional ultrasonic probe) Motor speed test pr
ADC
- CC2530采集ADC的电压值 并通过串口输出电压值,利用它可以采集很多模拟量传感器-CC2530 ADC and voltage values collected through the serial port output voltage value, which allows you to capture a lot of analog sensors
LED
- 通过I/O模拟同步串口与74HC595进行连接,控制74HC595驱动LED显示-light the led by 74H595 with I/O
STC_sample_PC
- 本程序在STC12C5A60S2平台上运行,通过对应的硬件原理图(文件名:SCH.pdf)中P1.0对模拟电压AD采集,模拟电压数值可以通过开发板平台按键改变,不同按键按下时对应不同模拟量,比如S6按下模拟量为2.5V, STC单片机对模拟量采样并在8位数码管前四位显示.2.5V采样后显示为2.500.同时采集的模拟量通过RS232串口可以传输到PC机接收,在串口调试助手上可以连续不断接收到采集的模拟量,该程序可以改变输入信号后直接用在数据采集项目或者毕业设计,课程设计.具有很强的通用性。-th
dingding
- 丁丁串口驱动,用于写串口通信时的模拟测试,不错-Ding Ding serial driver, used to simulate test write serial communication, good
7811
- 关于51单片机和dac7811芯片之间通信的程序,可以正确模拟SPI串口通信,写入数据-On communication between 51 single chip microcomputer and dac7811 chip procedures, can correctly simulate the SPI serial communication, write data
Verilog-RS232
- 本程序是在FPGA里面模拟RS232串口,并在已调试成功。-This procedure is simulated in FPGA RS232 serial port, and in the debugging success
code
- 基于ARDUINO平台将超声波采集的模拟信号转换成数字信息,然后利用串口通讯将数据(8位二进制)传送至PC端,利用相应的程序进行处理即可,本程序经调试已成功使用。-Arduino based development platform, analog data acquisition ultrasonic sensor converts the digital signal, and then sends the data through the serial port to the Pc sec
RemoteControl
- 通过发送串口命令来模拟电视机顶盒遥控器操作-Analog tv set-top box remote control operation by sending serial commands
51-USART-mpu6050
- MPU6050的51程序,采用模拟IIc总线,亲测可用,可以通过串口发送到计算机上面,然后通过串口波形软件即可显示波形,程序方便移植STM32-MPU6050 51 program, the simulation of IIc bus, dear test is available, can be sent through the serial port to the computer, and then through the serial port to display the wavefo
uart
- 基于verilog语言,使用FPGA对串口功能进行模拟与实现-Based verilog language, use the serial port function simulation and FPGA implementations
The-measurement-and-control-system
- 智能粮仓安全测控系统,支持注册人员登陆,登陆信息数据库管理,双向串口通信,模拟、数字电压采集,测试报表打印,测试数据数据库管理等-Safety monitoring system of intelligent granary, support the registration personnel landing, landing information database management, bidirectional serial communication, analog, digital
mini2440_simulation-SerialByIO
- 在mini2440上用IO口模拟的串口,采用异步通知的方式去通知进程串口数据读取完毕-Mini2440 on simulation of serial IO port asynchronous notification to inform the process of serial data read completed
upper-computer-serial-communication
- C#编写的windows应用程序,实现上位机与下位机之间的串口通信,实现对下位机的窗帘开关的模拟控制及状态查看,对烟雾浓度的检查,继电器的状态查询及控制。-C# windowsform serial port communication smart home
IIC
- STM32 GPIO模拟IIC串口,实现AT24C16页读写-STM32 GPIO IIC simulation serial port and realize AT24C16 page to read and write
a
- 本设计是以stc89c51为控制核心的秒表,利用单片机课程开发板作为主板,外接1602液晶显示。 本设计依照基本秒表的功能进行设计,通过独立按键的配合,能够完成计时的启动、停止、复位、定时等功能 同时本设计采用模拟远程控制,利用串口通信模拟远程控制秒表的启动、停止、复位等功能。 -The design is based on stc89c51 as the control center of the stopwatch, using SCM curriculum development bo
AA3
- 在PC上用串口控制DAC输出的模拟电压值,用这个 电压来驱动LED发光-On the PC with a serial control analog voltage output DAC with this Voltage to drive the LED light