搜索资源列表
LEDctrl
- keilc + proteus 并行口设计指示灯实验 要求：掌握80C51单片机输入输出接口使用方法 学会开关量输入输出控制的接口技术及编程方法 实验题目：8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。要求输出端口输出 “0”时，发光二极管亮。开关闭合时，开始按P1.0-P1.1-...-P1.7的顺序依次点亮LED，再按 P1.7-P1.6 -...-P1.0的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。-keilc
led
- 在和众达平台上，基于XV4FPGA开发外围驱动，使得led管循环点亮。-And Jones in the platform, based on the development XV4FPGA external drive, making led tube light cycle.
PWM_led
- PWM控制LED 灯做渐变的点亮（基于STC89C52单片机）-PWM control of LED lights do light gradient (based on STC89C52 SCM)
T0_ASM
- 51单片机定时器点亮LED灯，使其闪烁，定时时间可修改-51 MCU timer light LED lamp, it flashes, time period may be modified
led
- linux驱动 led灯的点亮，很实用，亲自调试，可以运行-linux driver led lamp light, very practical, personally debugging, you can run
LED
- 8个LED分两组,分别实现轮流点亮,给视觉以闪烁感-8 led spit two item, turn on or turn off
BIOStestdemo
- 基于ARM的S3C2440的BIOS测试例程和源代码 含点亮LED灯及LCD-ARM-based S3C2440' s BIOS test routines and source code with lit LED lights and LCD
LPM3
- msp430进入LMP3休眠模式，每4秒点亮LED灯-his program operates MSP430 normally in LPM3, pulsing P3.4 at 4 second intervals. WDT ISR used to wake-up system. All I/O configured as low outputs to eliminate floating inputs. Current consumption does increase wh
led1
- 练习单片机使用的基本程序，可以练习点亮led灯-SCM basic procedures used in practice, you can practice light led light
c51
- uc/os II移植 51单片机，包括工程文件和程序，实现在51单片机点亮led-uc/os II transplantation 51, including the project files and programs to achieve the 51 single-chip light led
Code
- SPCE061A做为主控制器对DM9000以太网控制芯片进行控制，完成以太网数据报的收发； 2. SPCE061A与DM9000构成的网络终端可以做为Web服务器，对局域网提供网页浏览服务； 3. 用户可以通过网页上的按钮实现对“空调”、“灯光”、“音乐”三个设备的控制； 4. 对设备的控制通过播报语音或点亮LED模拟代替。-SPCE061A do based on the DM9000 Ethernet controller chip controller to control t
LED
- 如何让51hei单片机学习板上的led灯点亮，一个很简单的程序，有详细的注释，适合刚入门的初学者学习锁存器的使用-How to light up 51hei microcontroller development board led light, a very simple procedure detailed notes, suitable for beginners to learn just started to latch
1.LED
- 1.LED cc2430 通过输出端口点亮灯管-1.LED cc2430 lit the lamp through the output port
Lab501-LED
- 最基础的用dm642的实现点亮流水灯的程序，初学很有用!-well dm642
led
- 点亮每一个led灯，让初学者感觉到学单片机的乐趣-Each led lamp light, so that beginners feel the fun of learning MCU
LED
- 如何使用LED循环点亮-How to use the LED lights cycle
I2C
- SMART（MAGIC）ARM2200 试验目的 学习编写I2C驱动及应用程序开发 掌握中断程序的开发流程 试验内容 响应按键，点亮对应的LED 按下按键1（S1）点亮LED1。。。，以此类推，按下按键4（S4）点亮LED4 按下按键15（S15）循环左移点亮LED 按下按键16（S16）循环右移点亮LED 完成上述每一步操作，同时要求把键值通过UART0回传到PC -SMART (MAGIC) ARM2200 purpose of study and p
02
- 利用单片机输出循环点亮LED灯D7~D0-Single Chip LED light output cycle using light D7 ~ D0
myled0321
- 使用的是mini2440开发板，开发工具为ads1.2.包含初始化程序，io口设置程序。点亮led-Using mini2440 development board, development tools for the ads1.2. Including initialization, io port setting process. Led light
SRAMreadwritetest
- 这是用verilog开发的外部SRAM测试程序，编写了SRAM的读和写，当读写值相同则点亮LED。在实际测试中检测是正确的。对调试SRAM的朋友有一定的参考价值-It is the development of the external SRAM with verilog test procedures, preparation of SRAM read and write, read and write the same value when the light LED. In the act