搜索资源列表
SFR-dianliang--LED
- 51单片机源程序，SFR地址操作点亮LED，适合初学者，感谢下载-51 microcontroller source, SFR address operational lit LED, suitable for beginners, thanks for download
LED
- 本程序提供两种点亮LED的方法，希望对单片机初学者有用处-This programme is for a new learner
LED
- 按一下开关可点亮LED，手放开后保持着明亮状态，然后再按一下开关，LED才会灭掉，以此类推。-Press the switch to light up LED, after holding a bright state hands off, and then push the switch again, LED will burn out, and so on.
1-LED
- stm32单片机初级教程，如何点亮LED灯-stm32 SCM primary curriculum, how to turn on LED lights
Light-up-the-LED
- 基于C51单片机点亮LED灯为初学者提供一个基础的学习。-Based on C51 lit LED lights provide a basis for beginners to learn.
LED
- stm32点亮LED灯程序，keil工程可执行。-stm32 lit LED lights procedures, keil project executable.
2-LED-1X1C
- PIC18F4520点亮LED程序,适合初学者-PIC18F4520 LED PROGRAM
LED
- BLE4.0低功耗蓝牙技术开的基础实验，点亮LED-basic sources of BLE4.0 on the IAR
led
- 单片机点亮led小灯，适合初学单片机的学生们。-MCU light led a small light, suitable for beginners microcontroller of the students.
STM32F051-led
- STM32051系列单片机的源码程序，点亮LED- STM32051 MCU source program, lit LED
lpc2138-LED
- LPC2138 IO口实验，通过点亮LED灯观察实验现象-LPC2138 IO port
LED
- * 功 能：CC2530基础实验 - 点亮LED实验 * * 硬件连接：led灯端口：p1.0, p1.1, p1.3, p1.4：-* function: CC2530 based experiment- light LED experiment * * * 硬件连接：led灯端口：p1.0, p1.1, p1.3, p1.4： * hardware connection: LED lamp port: P1.0, P1.1, p
led
- DSP点亮LED灯 一个完整的工程项目 适用于TI系列C66X系列DSP-DSP light LED light a complete project
LED
- 利用QuartusⅡ IPCore实现循环点亮LED.-Use Quartus Ii IP Core for recycling lit LED.
led
- 基于亚龙实验台点亮led单个小灯的实验， 适合初学者。-Based Yaron bench lit a small lamp led single experiment suitable for beginners.
ALIENTEK-MINISTM32--led-
- ALIENTEK MINISTM32 实验1 跑马灯，为初学者提供点亮LED灯的模板-ALIENTEK MINISTM32 Experiment 1 Marquee
led
- 8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。 要求输出端口输出“0”时，发光二极管亮。 开关闭合时，开始按P0.0+P0.7、P0.1+P0.6、P0.2+P0.5、P0.3+P0.4的顺序依次点亮LED，再按P0.3+P0.4、P0.2+P0.5、P0.1+P0.6、P0.0+P0.7的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。 开关断开时，立刻停止点亮指示灯。 -Eight light-emitting diodes
Item-two-LED-cycle-light
- 循环点亮LED灯，实现每隔几秒钟轮流点亮，简单实用，可以自己动手做做，还配有电路图-Cycle lit LED lights, to achieve every few seconds turn light, simple and practical, you can do it yourself, but also with a circuit diagram
LED
- STM8S003F3 DEMO例程，点亮LED 灯，无外部晶振，最小例程，基于IAR 编译器。-STM8S003F3 DEMO u4F8B u7A0B uFF0C u70B9 u4EAHR09 u708F uFF0C u65E0 u5916 u90E8 u6676 u632F uFF0C u6700 u5C0F u4F8B u7A0B uFF0C u57FA u4E8EIAR u7F16 u8BD1 u5668 u3002
main
- 根据STM32寄存器地址，配置P0~P3为推挽输出，点亮LED灯。(According to the STM32 register address, the configuration P0~P3 is push-pull output, and the LED lamp is lit.)