搜索资源列表
rf_decode
- 万能无线解码,最重要的是事以解出振荡电阻阻值,非常难得。-Universal wireless decoder, the most important thing is to solve the oscillation resistor, very rare.
plotSmithChart
- 绘制史密斯圆图。包括电阻圆和电抗圆。欢迎指正-Drawing Smith chart. Including resistance and reactance circle round.
lilei127-01
- 我是新人,很高兴通过朋友介绍得知这个网站。动态显示的特点是将所有位数码管的段选线并联在一起,由位选线控制是哪一位数码管有效。这样一来,就没有必要每一位数码管配一个锁存器,从而大大地简化了硬件电路。选亮数码管采用动态扫描显示。所谓动态扫描显示即轮流向各位数码管送出字形码和相应的位选,利用发光管的余辉和人眼视觉暂留作用,使人的感觉好像各位数码管同时都在显示。动态显示的亮度比静态显示要差一些,所以在选择限流电阻时应略小于静态显示电路中的。 -I was new, I am glad that t
codeID
- PT2262软件解码程序,不用定时器,不用中断,代码最少。发射端为PT2262 3.3M 的电阻 接收端为 M8 内部1M RC振荡。解码成功后输出D口显示。编译软件为 ICCAVR。 -PT2262 software decoding process, no timers, without interruption, the code minimum. Transmitter for the PT2262 3.3M resistor receiving end for the M8 inter
wanyongbiao-
- 简易数字万用表仿真\测电流 电压电阻 电感电容-Simulation of simple digital multimeter
diancanshu
- 基于STM32的电参数测量程序,测电阻时使用555定时器,根据多谐振荡频率测得电阻值-STM32-based electrical parameters measurement procedures, the use of the 555 timer measuring resistance, according to the multi-harmonic oscillation frequency measured resistance value
8051-ADC-using-an-AD1674
- 这种设计展示了一个80C51单片机用来控制AD1674模数转换器。 当仿真运行调整可变电阻,观察其 在虚拟终端的数字值。图显示了控制信号 可以重新在仿真计算已停止。-This design demonstrates the use of an 80C51 to control an AD1674 ADC. When the simulation is running adjust the variable resister and observe its digital v
electronic-contest-program
- 此程序是我参加山东电子设计竞赛时写的电阻电容电感测量仪的整个程序,包括了各种驱动程序、控制程序、测量采样程序、显示程序、遥控输入程序。里面的一些程序适合给很多人作为参考,我基于AVR单片机来写的。-I participated in this program is to write Shandong Electronic Design Contest resistance capacitance inductance meter the entire process, including the
xiaodianzu
- 考虑小电阻接地的配电网络可靠性分析的matlab程序-Reliability analysis of low resistance grounding
NTC_Temp
- 一个将NTC热敏电阻转化为 AD>>温度 对应数组的程序,并以图形方式体现出来,可以用来确定上拉电阻和下拉电阻合适否。回车键退出,参数输入方式见main开头办法。(上拉电阻和下拉电阻均有 不同的基准电压均有考虑 )-An NTC thermistor will be converted to AD > > temperature corresponding array of procedures, and graphically reflected pull-up resi
LCR_DIY
- 自制LCR表,可以测量电感,电阻,电容及其大部分参数;精度<1 可以作为参考。-Homemade LCR meter that can measure inductors, resistors, capacitors and most of its parameters accuracy <1 can be used as reference.
DB25-JATA10
- 这是用于ALTERA公司CPLD/FPGA芯片的并口下载器,里面的电阻、电容的参数都是对的,是成熟产品的并口下载器设计方案。-This is used ALTERA chip CPLD/FPGA parallel port download, parameters of resistance, capacitance inside is all right, is a mature product parallel download device design scheme
12KGR1
- 无线遥控学习型12继电器开关,功能有上电记忆、全开和全关,用PIC16F57单片机做的,要求相当于PT2262 4.7M的振荡电阻!-Wireless remote learning 12 relay switches, power memory function, fully open and fully closed, with the PIC16F57 microcontroller to do, requiring the equivalent PT2262 4.7M oscillati
STM32AD
- 实验说明: 1、配置GPIO的时候,要将PC3设置成模拟量输入,模拟量的大小是0-3.3V之间 可以通过精密可调电阻改变输入电压大小。 ** 实验现象: 1、通过JLINK下载后,按下“reset”键,程序开始运行。 2、屏幕打印“FireBull ADC_example”时,开始接收转换结果,以数字量的形式输出。 3、旋转板子上的可调电阻时,可以看都数字量的改变。-Experiment: 1, configurable GPIO when
touch_screen
- 电阻屏触摸驱动 直接读取寄存器电平值的到xy坐标,不需要SPI操作。-Resistive touch screen driver directly read the register level values to xy coordinates, no SPI operation.
PID-temperature-control-based-on-51
- 用51单片机实现电阻炉的水温控制系统,将温度稳定到设定的温度,并每隔五秒将实时温度值通过串口发送给电脑(外围器件为光+可控硅)-MCU with 51 resistance furnace temperature control system, the temperature was stabilized to the set temperature and real temperature value every five seconds will send to the computer t
DegreeControl
- 基于C51单片机的温度控制小程序,通过两路PWM输出控制一个水泥电阻的温度,用DS18B20完成温度的检测,LCD1602显示,里面有一个简单的闭环控制子程序,欢迎参考。-C51 microcontroller-based temperature control of small procedures, through the two PWM outputs to control a temperature of the cement resistor, complete with temper
QQjuZshuMG
- 基于MSP430G2553 开发环境CCS 做的电阻测量仪源代码-jiyu kan ni ge da tou bao
language
- 电阻与温度的比例模糊算法,适合编程开发使用!-The ratio of resistance and temperature fuzzy algorithm for programming development and use!
R_TEST
- 使用MSP430G2553制作电阻测量仪,LCD1602显示,使用430内部AD,编译环境为IAR-Use MSP430G2553 making resistance measuring instrument, LCD1602 display, use 430 internal AD