搜索资源列表
RTC
- 基于LPC2148的 RTC通过串口发送到PC机查看 用的是IAR+jlink V8-Based on the RTC LPC2148 sent to the PC via the serial port using a machine view IAR+ jlink V8
AN_119_FTDI_Drivers_Installation_Guide_for_Window
- This file is fot ft2232 jlink.
Setup_JLinkARM_V408l
- 该软件为jlink v7的驱动程序，对于v8也同样适用，主要用于嵌入式开发-The software driver for the jlink v7, v8 is also applicable for mainly used for embedded development ......
123
- Micro2440 开发板 的Jlink 的初始化文件-Micro2440 initial file on the Plantform of Jlink
JLINK
- 驱动程序,帮助将电路板通过仿真器成功与电脑相连.-Driver, to help the board through the emulator successfully connected to the computer.
LED
- 1设计要求 PC6,PC7,PD6,PD13 LED快速交替闪烁。 2 硬件电路设计 在开发板上通用I/O口PC6,PC7,PD6,PD13作为控制D1,D2,D3,D4的控制线。 3软件程序设计 根据设计任务要求，软件程序主要包括： (1) 配置GPIO口，将PC6,PC7,PD6,PD13配置为上拉输出模式。 (2) 延时控制相应端口的置位和复位。 4 运行过程 (1) 使用Keil uVision3 通过
TQ2440_jlink-AXD
- TQ2440关于JLINK调试的文本，试了，可以调试！但要更多了解AXD+JLINK还要多参考其他资料！-TQ2440 JLINK debugging on the text, test, and you can debug! But to learn more about AXD+ JLINK even more reference to other information!
firmarmRev6396d
- jlink firmware v6.0 burned and tested working after AT91SAM TST sam-ba reload
JLink_Linux_V440a.tar
- This SEGGER JLink commander tool. Which is used for download your program to ARM boards.-This is SEGGER JLink commander tool. Which is used for download your program to ARM boards.
IARPJLINKv5
- arm iar jlink 调试步骤说明-arm iar jlink arm iar jlink
v8_ID-12345678
- JLINK v8固件arm仿真器程序，直接烧写就可以-JLINK v8
sdram_init_s3c6410
- 压缩包是使用JLink间接烧写s3c6410 nand_flash的源代码及可执行文件。由于s3c6410不像s3c2410那样有nor flash，可以方便的使用JTAG接口烧写引导程序。压缩包内的代码可以根据http://hi.baidu.com/__eabi/blog/item/5bfceaadf90eb39146106426.html帖子的说明，借助ADS1.2开发环境和JLINK，烧写二进制程序到开发板。 文件说明： sdram_init_s3c6410 | 、—
JLink_Linux_V441g.tar
- JLINK full software for linux
u-boot-1.1.6_OpenJTAG
- 使用JLink间接烧写S3C2410、S3C2440开发板Nor、Nand Flash源码在线！--The use of indirect JLink programmer S3C2410, S3C2440 development board Nor, Nand Flash source online!
Jlinksource
- Jlink调试资源，有助于arm裸机调试-Jlink debug resources to help arm bare metal debugging
STM32display
- STM32的显示模块，很有用处啊，可以直接用jlink仿真-display module in STM32, direct use
STM32F107VCPKeilPv4.12PjlinkPv8
- 写给入门级STM嵌入开发者的STM32F107+Keil v4.12+jlink v8在SRAM环境中调试程序设置，详细介绍了KEIL环境下对ROM和RAM的地址设置-For entry-level STM embedded developer STM32F107+Keil v4.12+jlink V8 in the SRAM environment debugging program, introduced in detail the KEIL environment for ROM and
KeilMDK3.5DEBUG
- stm32的调试，KEIL MDK 3.5/4.0的Jlink调试SRAM-STM32 debug，use JLINK TO DEBUG THE SRAM ON KEIL MDK
update_jlink_v8
- JLink_V8固件升级软件及升级文件！ -JLink_V8 firmware upgrade software and upgrade files!
JLINK
- J-LINK V7 , DIY PACKAGE-The J-Link V7, DIY PACKAGE