搜索资源列表
uart_top
- UART的verilog代码，tx，rx皆可-Verilog code of UART, tx, rx Jieke
Lab_UART_Correct
- usart rx/tx stm32f10x
UartExample7
- 使用宏定义的某个串口发送数据,包括remap串口，可以用于测试。-stm32fxx usart tx rx for all,with remap
benchmark-tx-rx.tar
- 自己修改过的USRP收发程序，可以实现两个USRP之间的数据传输-USRP receive their modified procedure, can achieve data transfer between two USRP
RS232
- VB RS232 RX and TX data with visual basic source code and using DLL library-Visual RS232 VB program example
fet140_spi0_07
- Descr iption: SPI Master communicates at fast as possible, full-duplex with // SPI Slave using 3-wire mode. The level on P1.4/5 is TX ed and RX ed to P1.0 // and P1.1. Master will pulse slave Reset on init to insure synch start. // Master norma
fet140_uart01_0115k
- // Descr iption: Echo a received character, RX ISR used. Normal mode is LPM0, // USART0 RX interrupt triggers TX Echo. // ACLK = MCLK = UCLK0 = LFXT1 = 8MHz // Baud rate divider with 8Mhz XTAL = 8000000/115200 = 0069 (0045h) // //* An externa
TX-RX-Project
- This an example for Short distance RF data communication.In this project some parameters Temperature,pressure recevived from sensors digitalized and converted to serial , finally transmitted through air . This data received in another unit and the op
si4432-485-rx
- STC10L SI4432 MAX485组成的无线485协议接收端 用于无线485的传输（监控云台控制）-STC10L SI4432 MAX485 protocol consisting of 485 wireless receiver for wireless transmission of 485 (control PTZ control))
01.RF-Interface-Rx-Tx-Auto_Normal
- This the program to communicate between to cc2500 Module in Normal Mode.-This is the program to communicate between to cc2500 Module in Normal Mode.
05.PC-Ctrld-robot_Wireless
- This is the program to communicate between PC and robot with cc2500 Module as TX Rx.
usbDevMuch
- LPC1700芯片USB批量传输源码。只要修改读写信号线以及PID、VID即可立即运行-Source code of USB Driver for LPC1700。You can run it imediatly only if you modify the RX/TX and PID/VID
3497
- simple rx from 3s9b92-simple rx from 3s9b92
cc2500_TI
- Working chipcon/TI cc2500 Lib. bitrate reg set to 10kbaud. recieve packet on GD0 int or GD2 goes high to indicate RX/TX overflow. flush and continue
FX589_TX-and-RX(2011.12.10.15.37)
- 本程序是基于c8051f330单片机的FX589的GMSK同步无线通信程序，希望对大家有用。-This procedure is based c8051f330 microcontroller FX589 GMSK synchronized wireless communication program the hope that useful.
CE401_ECAN_Mode0_with_Baud
- can rx mode with baud rate 0
point
- 点对点无线基本通信（仅实现发送接收 不含其它的成分）-point to point RX and TX
CC2530-UART2TEST
- descr iption：CC2520UART1-TX&RX-RECEIVE AND TRANSIT
ON-CHIP-PROGRAMS_PIC16F877
- the contents are pic16f877 programme for ADC, PWM and SERIAL TX and Rx-the contents are pic16f877 programme for ADC, PWM and SERIAL TX and Rx...
nRF24LE1
- nRF24LE1收发源码,最基本的键盘程序demo-nRF24LE1 Rx or Tx