搜索资源列表
vehicle-bridge-coupled
- ANSYS车桥耦合瞬态分析代码,实现车辆移动荷载加载-ANSYS-vehicle bridge coupled
impact-example
- 通过ansys画出模型后，前处理得到模型数据，导入fortran中计算模型受力情况，最后得到模型的变形情况-After the draw by ansys model, pre-treatment to obtain model data, import fortran model calculated the forces, and finally get deformation model
RME_BEAM3
- 采用ANSYS建立的轨道模型，请有需要的人自行下载-The rail model was established by using BEAM3 element
welding_DUF
- 焊接领域的流体力学仿真计算，采用ANSYS fluent 编写的UDF，适用于初级教学或者入门级学者进行分享学习-Fluid dynamics simulation field of welding, using UDF ANSYS fluent written to share learning applies to primary education or entry-level academics
anqiao
- ANSYS港口起重机建模，ansys内置命令流建模，大梁结构至起升机构都仔细画出-Port crane modeling, ANSYS built-in command flow, easy and convenient modeling.
tsyde-22
- Modélisation de MAS par Maxwell Ansys
truss_on_matlab_new_stress
- 基于应力比法的三杆桁架结构优化实现，有限元分析调用ANSYS，使用时需修改相关文件路径。-optimization of truss structure based on stress ratio method
laser-deposition
- 利用Ansys分析激光沉积温度场，应力场的的apdl源程序-laser deposition
uel101
- ansys通用有限元程序 link8单元 uel101用户子程序-ansys link8 uel
考虑焊钉刚度波形刚腹板箱梁
- 用于ansys有限元分析，考虑焊钉滑移刚度，波形钢腹板(For ANSYS finite element analysis)
banhuang
- 1、本程序实现了车辆板簧装配过程和承载力计算的参数化分析 2、程序分为两个荷载步，荷载步1为板簧的装配，荷载步2为板簧的承载力计算(1, this program implements the parametric analysis of the leaf spring assembly process and the calculation of the capacity of the vehicle 2, the program is divided into two loading s
小箱涵配筋计算
- 箱涵配筋的方法及计算进行一些说明，对每一步都有详细说明。(The method and calculation of the reinforcement of box culvert are explained in detail and each step is described in detail.)
AMR.718-720.2184
- 层析粒子图像测速技术 ART MART 图像分析 图像识别(tomograhic particle image velocimetry ART MART image ansys)
CONDUCTOR
- 可以在ANSYS中运行的命令流，能够用于导线的模态分析(The command stream that can run in ANSYS)
Fluent UDF教程+Ansys Fluent 14.0 UDF手册
- 水蒸气与空气按质量分数混合后的物性参数质量加权平均——fluent udf 源文件(The mass average of the physical parameters of the mixture of water vapor and air by mass fraction)
TOWER
- 钢塔整体建模分析，包括重力荷载及风荷载计算(Analysis of the whole tower modeling, calculation of gravity and wind loads including)
Stepped_cylinder
- Stepped cylinder for fluent analysis with ANSYS
creep stress relaxation of bolt
- apdl 用于蠕变分析，此案例主要用于单向螺栓的蠕变情况，根据APDL的批处理优点特性，可更改加以重复验证信息。(creep analysis using apdl)
厚壁圆筒塑性分析
- 用于处于内压作用下厚壁圆筒的塑性分析，观察其塑性状态和屈服状态(for thick-walled tube under the inner pressure to observe the plastic state or judge if it has been yielded/)
飞轮建模
- 用于基本的机械领域的飞轮建模分析，熟悉apdl的基本建模技巧(for modling the flywheel by using the apdl)