搜索资源列表
ucosII_i2c
- 周立功公司的ARM开发板LPC2119环境下,I2C总线读写驱动程序。该代码可以重入。可直接使用无须修改。-the development board LPC2119 ARM environment, I2C bus driver to read and write. The code can go back to. Direct access needed to be changed.
jx44b0study_system_souce_code
- 压缩包里包含有JX44B0教学实验系统用户手册及该系统的全套试验例程,用c编写,在ADT环境下编译后下载到 实验板即可执行,是学习arm开发的有用例程 源文件说明 Leddemo LED显示实验 Led LED 显示实验 Serial 串口实验 Interrupt 外部中断实验 Dma DMA实验 Pwm PWM实验 Rtc 实时时钟实验 Watchdog 看门狗实验 Ad AD 采样实验 St
kaidri4
- 这是一个基于s3c2410的驱动,通过16位总线arm取CPLD得到的数据-based s3c2410 driven by 16 bus arm from the data obtained from the CPLD
CANbusdriverforS3C2410
- CAN总线芯片MCP2510在ARM芯片S3C2410上的完整驱动程序,MCP2510通过SPI接口与S3C2410对接,在Linux2.4操作系统下实现了底层带CAN接口的智能设备与上层设备进行通讯。-MCP2510 CAN Chip Chip S3C2410 ARM in the integrity of drivers, MCP2510 through the SPI interface and S3C2410 docking, the Linux operating system und
fft2410-can
- 基于三星2410嵌入式平台,实现can总线的驱动及使用,适合搞arm 控制的朋友们
UPCAN
- CAN总线设备驱动,已在Linux2.4测试通过。CAN控制芯片MCP2510,微处理器S3C2410,交叉编译环境arm-linux-2.95.3.
SPI_LED
- 运行于ARM lpc2200系列的程序源代码,使用SPI总线控制一位数码管循环显示数字.使用595芯片驱动数码管.
CAN
- s3c2410 arm实验箱关于Can总线的驱动代码。代码条理清晰,注释详细。非常有价值。
Exp5LCDqudongkongzhi
- 学习LCD显示器的基本原理,理解其驱动控制方法。掌握两种LCD驱动方式的基本原理和方法。并用编程实现: 1.用总线方式直接驱动带有驱动模块的LCD。 2.用ARM内置的LCD控制器来驱动LCD。
USB_I2C_program1
- 移植了可运行于arm lpc2294下的uc/os2,且具有完整的pdiusbd12 通信驱动程序,能进行上下位机的通信,还完成了iic总线的控制,完成eeprom的读写。
lcd
- pxa270的LCD控制。 用总线方式驱动LCD模块,实现ARM内置的LCD控制来驱动LCD.
sja1000-driver
- arm扩展can总线的驱动程序-arm can extend Bus Driver
UDA1341.WAV.DRIVER
- 此源码为UDA1341音频芯片的播放WAV驱动,可以配合I2S总线,在ARM微控制器下可以实现高保真录音和回放。-This source for UDA1341 play WAV audio chip driver, you can tie in with the I2S bus, in the ARM microcontroller can achieve high-fidelity sound recording and playback.
canbus
- 基于ARM S3C2440的CANBUS总线的驱动程序,can 主IC为MCP2510,CAN 正负脚应该接120R 跨阻-Based on ARM S3C2440' s CANBUS bus driver, can the main IC for MCP2510, CAN feet should take positive and negative cross-resistance 120R
I2cInt_c
- LPC2200系列ARM处理器中I2C总线的驱动程序-LPC2200 series ARM processor I2C bus driver
CAN
- linux下基于arm处理器s3c2410x开发板的CAN总线设备驱动程序以及数据发送和接收的程序代码。-arm processor linux-based development board s3c2410x the CAN bus device driver, as well as send and receive data on the program code.
MCP2515_driver_s3c2440based
- 本驱动程序在s3c2440上实现了两路基于SPI的CAN总线控制器。两通道可以并行,并使用外部定义的两个信号量来通知接收任务收到CAN总线帧,并将其存入预先定义的队列中(帧定义在CAN总线控制器驱动程序的头文件中)。CAN总线控制器的中断引脚分别连接到ARM的EINT3和EINT8_23上-The driver s3c2440 achieved a two-way SPI-based CAN bus controller. Two channels can be parallel, and us
can_driver.tar
- arm 2440 web远程控制开发板can总线驱动-arm 2440 web can control
CAN2Ethernet-W5500-STM32
- 采用W5500芯片。一种较新的以太网转CAN总线的解决方案,开发板,CAN转以太网选用意法半导体的Cotex-M3的32位微控制器STMF103C8T6.板载W5500以太网内置协议栈,可实现TCP/IP,UDP,WEB等。内含开发板介绍,原理图和Keil MDK ARM的驱动程序。-Using W5500 chip. A relatively new Ethernet to CAN bus solutions, development boards, CAN-to-Ethernet choic
zynq axi dma驱动程序
- 基于zynq嵌入是linux axi dma驱动程序代码,可利用axi总线实现arm与fpga数据交互。