搜索资源列表
danpianjipaomadeng
- 系统配置完，进入while(1)循环，开始扫描端口变化(上升沿)，如果有则进入相应的执行语句，采集端口信息，用了库函数此例程通过按键控制LED亮灭，熟悉了对端口的简单操作。-1, the system has finished configuration, enter the while (1) loop, start scanning port change (rising), if you enter the corresponding statement is executed
serial-communication
- 51单片机与上位机之间的串口通信 控制LED亮灭并发送到上位机 -51 and serial communication between the host computer to control the LED light off and sent to the host computer
threelift
- （1）、每层电梯入口处设有上下请求开关，电梯内设有顾客到达层次的停站开关。 （2）、设有电梯入口处位置指示装置及电梯运行模式(上升或下降)指示装置。 （3）、电梯每秒升(降)一层楼。 （4）、电梯到达有停站请求的楼层，经过 1 秒电梯门打开，开门指示灯亮，开门 4 秒后，电梯门关闭(开门指 示灯灭)，电梯继续进行，直至执行完最后一个请求信号后停留在当前层。 、能记忆电梯内外所有请求，并按照电梯运行规则按顺序响应，每个请求信号保留至执行后消除。 、电梯运行规则当电梯处于上升模
SourceCode08_Key4
- DSP2812上的键盘例程,键盘按下,IO口输入变低后,输出的IO口控制led亮灭,编译环境为CCS3.3-DSP2812 keyboard routines on the keyboard is pressed, IO port input goes low, the output of the IO population control led light off, the compiler environment CCS3.3
webpage-control-zigbees-led
- 本程序实现静态网页控制zigbee的led亮灭，实现zigbee与arn的结合-The program s static pages control zigbee led light off, realize the combination of zigbee with arn
8_1_TouchPad_LED
- G2553开发板，触摸来改变LED的亮灭。-G2553 development board touch to change the LED light off.
LED8
- Atmega128IO程序，8位独发光二极管闪烁，通过IO口控制8位发光二极管的亮灭。开发环境：GCCAVR-Atmega128IO program, eight single LED flashes, through the IO port control eight light-emitting diode light off. Development Environment: GCCAVR
KEY4
- Atmega128，独立键盘控制程序，通过扫描方式检测按键，并控制相应发光二极管的亮灭。开发环境：GCCAVR-Atmega128, separate keyboard control program, by scanning detection button, and control the corresponding light-emitting diode light off. Development Environment: GCCAVR
serial_port
- STC52单片机串口测试程序，上位机通过串口控制LED亮灭-STC52 microcontroller serial testing procedures, the PC via the serial port to control the LED light off
led
- 嵌入式平台上的LED驱动程序和应用程序 以及MAKEFILE文件 实现LED的亮灭等-LED drivers and applications, and MAKEFILE files embedded platforms to achieve LED light off, etc.
2112312
- 模拟交通灯实验，实验报告 用 8255 做输出口，控制十二个发光管（4 组红绿黄灯）的亮灭，模拟十字路口交通灯 管理。-Simulated traffic light experiments report To do with the 8255 output, control twelve light tube (4 groups of red, green yellow) light off, analog crossroads traffic lights Managem
led_control(receive)
- VC++通过串口自定义通信协议控制LED等亮灭。-VC++ LED light off and other custom communication protocol via the serial control.
led_control(send)
- vc++通过自定义通信协议控制LED灯亮灭(Send端)-VC++ LED light off and other custom communication protocol via the serial control(send).
mini2440_leds
- mini2440上LED驱动程序，对引脚进行配置后，对寄存器进行操作已实习LED的亮灭-mini2440 LED driver pin configuration register internship LED light off
heart-led
- 用51单片机控制围成心形形状的32个led亮灭-Surrounded by 51 MCU control deliberately shape of 32 led light off
TLC5615
- 通过51控制TLC5615 通过LED的亮灭来显示TLC5615的工作情况 -Chips and combine TLC5615 51 through LED display light off of work TLC5615
watchdog
- 基于samsung6410开发板的watchdog裸板驱动，通过控制watchdog，喂狗，产生中断，控制led的亮灭-Drive watchdog bare board based on the samsung6410 development board, by controlling the watchdog, feed the dog, interrupt, control LED light off
STM32L151Penc28j60--web-control-led
- 用STM32+ENC28J60做的以太网TCP/IP协议开发实例，通过WEB页面可以控制LED的亮灭，同时可以进行温度的采集。完整版代码。-To do with the STM32+ ENC28J60 Ethernet development example, by WEB pages can control the LED light off, while the temperature of the acquisition. Full version code.
LIGHT-001-1
- 三个灯循环渐明渐暗，3v 6小时亮，18小时灭； 低电平定时6小时，高电平不定时。-Three light cycles slowly fades, 3v 6 hours light, 18 hours off Low timing six hours, a high level time to time.
traffic_simple
- 基于Verilog的简易交通灯控制。//主干道绿灯亮30s，最后5秒绿灯灭黄灯亮，30s过后红灯亮起，倒数20s后绿灯亮30s，如此重复 //支干道红灯亮30s，后绿灯亮，支干道绿灯倒数20s，最后5s绿灯灭黄灯亮，20s倒数完后换红灯亮30s，如此重复-Verilog-based simple traffic light control. // Main road green light 30s, the last five seconds off the yellow light gre