搜索资源列表
456
- 点亮led灯,通过单片机控制led灯的亮灭,程序觉对可用,简单-SCM control lighting led lights led lamp light off, procedures sleep on the available
22222
- 基于单片机的独立开关控制系统,一个按键来实现灯的亮灭-Based microcontroller independent switch control system, a key to achieve the lamp light off
VMD642_led
- dsp板led灯控制程序。通过改变led灯寄存器的值,来控制等的亮灭。-The dsp board led lamp control procedures. By changing led lamps register value, to control the light off.
danpianjizhongduanfangzhen
- 单片机仿真。proteus环境内。包含仿真,源文件,kell文件。内容:51单片机中断控制,使得LED灯1秒亮灭,60秒亮灭,1小时亮灭。-SCM simulation. proteus environment. Including simulation, source files, kell file. Content: 51 microcontroller interrupt control, LED lights light off one second, 60 seconds light
PIT_a_EXTI
- K60的定时中断和外部中断,可以实现进入定时中断循环点亮2个LED灯,同时嵌入外部中断,控制LED亮灭-K60 the timer interrupt and external interrupt, lit two LED lights into the timer interrupt cycle, while embedding external interrupt control the LED light off
ExInt
- DSP28335的外部中断,可以控制LED灯的亮灭顺序-DSP28335 external interrupt, you can control the LED lights light off order
8255
- 微机实验8255 1)用8个LED来反映8个开关量的状态,拨动开关,让对应的灯亮。 2)8255控制交通灯 本设计用LED来模拟交通灯。请考虑8255与LED的连接,以及如何用8255来控制LED的点亮与熄灭。 交通灯的控制过程: 东西向的绿灯、南北向的红灯亮5秒钟。 东西向的绿灯灭、南北向的红灯亮,在此时间段中东西向的黄灯闪烁5次,每次亮0.5秒灭0.5秒。 南北向的绿灯、东西向的红灯亮5秒钟。 南北向的绿灯灭、东西向的红灯亮,在此时间段中南北向的黄灯闪烁5次,
light
- 基于linux retHad gec2440(ARM9)上开发的灯驱动,在gec2440(ARM9)板上实现点灯,关灯的功能。-Developed based on linux retHad gec2440 (ARM9) lamp driver in gec2440 (ARM9) board lighting, turn off the lights.
exp2
- 流水灯的实验,正转反转等功能,实现流水灯顺序亮灭。-Light water experiments, are forward reverse function, water lamp light off sequentially. .
light_show
- android控制arduino led亮灭-android control arduino led light off
LED_VHDL
- 用VHDL控制发光二极管,点亮发光二极管在熄灭发光二极管-VHDL control light off of the light-emitting diodes
asfart
- 函数法的流水灯 有别于数组法流水灯实现8位灯的亮灭-Function method of light water is different from the array method light water eight lights light off
ex1
- 使用EDA实验箱上的脉冲,进行分频,通过波形仿真和观测实验箱上输出指示模块中的OUT1红色LED(发光二极管)的亮灭时间来验证是否符合设计要求。-Using the the EDA experimental box on the pulse divide output by the waveform simulation and observations on the experimental box the indication module OUT1 red LED (light emitt
PAOMADENG
- 该程序实现LED的闪烁,每隔0.2秒更替一次亮灭-The program LED flashes every 0.2 seconds replacement light off
Light-LED-circulating
- 小小游戏机:利用8255芯片完成,8255芯片接有LED灯和按键。 1、LED灯初始状态为循环点亮; 2、按键和灯是一一对应的状态,如果在灯n(n=1--8)点亮的时候,按键被按下,则游戏成功,所有灯灭。如果按键n(n=1--8)按下时,相应的灯n没有亮,而是其他灯亮, 则游戏失败,所有灯继续处于循环点亮状态。-Little Rides: the completion of the 8255 chip, 8255 chip connected with LED lights and bu
jiaotongdeng
- 考虑横道线的交通灯的控制,设有红,绿两盏信号灯,一般是红的亮,路边设有按钮SF, 行人横穿街道时需要按一下按钮.4s后红灯灭,绿灯亮,过5s秒后,绿灯闪烁4次然后红灯又亮-Consider zebra stripes control of traffic lights, with red, green two lights, usually red bright side of the road with button SF, pedestrians crossing the street ne
watchdog
- 定时模式:将WDT设置为定时模式产生定时中断,控制P1.0的输出,使LED周期亮灭。 看门狗模式:将WDT设置成看门狗模式,此时,当看门狗定时器溢出时,将会产生复位。 -Timing mode: WDT setting the timing mode timer interrupt, control the P1.0 output, the LED cycle light off. Watchdog mode: WDT set watchdog mode, at this time, w
pwmled
- 基于k60单片机用pwm控制led的亮灭-Based k60 microcontroller pwm control led light off
STM32F103-GPIO
- STM32F103 的控制GPIO口操作,控制LED指示灯的亮灭,,写1,写0-STM32F103 control GPIO port operation, control the LED light off, and write one, write 0
BK-DK5438
- msp4305438的两个程序,一个是串口控制发光二极管的亮灭,另一个是TI公司的DAC5571程序,DA输出电压再通过ADC12把电压读出,用数码管显示出来,还可以实现按键调节电压值。这两个程序纯属自己的原创,并在IAR仿真调试通过,移植起来也很方便。-msp4305438 two programs, one is serial control LED light off, the other is TI' s DAC5571 procedures, DA output voltage