搜索资源列表
dong-tai-jian-mo-fangzhen
- 包含实验一、直流电动机建模及仿真实验 及实验三、考虑结构刚度时的直流电动机-负载建模及仿真实验的程序源码及实验报告-Contains the experimental one, the DC motor modeling and simulation，and the Experiment 3, the DC motor when considering the structural stiffness- load modeling and simulation program sourc
bujindianji--C
- 步进电机是将电脉冲信号转变为角位移或线位移的开环控制元步进电机件。在非超载的情况下，电机的转速、停止的位置只取决于脉冲信号的频率和脉冲数，而不受负载变化的影响，当步进驱动器接收到一个脉冲信号，它就驱动步进电机按设定的方向转动一个固定的角度，称为“步距角”，它的旋转是以固定的角度一步一步运行的。可以通过控制脉冲个数来控制角位移量，从而达到准确定位的目的；同时可以通过控制脉冲频率来控制电机转动的速度和加速度，从而达到调速的目的。-Stepping motor is will signal into
2_9
- AN ADAPTIVE CONTROLLER BASED ON NEURAL NETWORKS FOR MOTOR-DRIVE LOAD SIMULATOR Shen Dongkai Wang Zhanlin College of Automation Science and Electrical Engineering Beijing University of Aeronautics and Astronautics Beijing 100083, P.R.China r
pppi.mdl
- 同步电机的矢量控制，控制效果令人满意，能在较短时间内跟随负载而转速不受影响-Synchronous motor vector control, control was satisfactory, and in a relatively short period of time to follow the load and speed is not affected
power_control_sys
- ATmega16控制的智能电机控制器 2路大电流检测，负载状态控制 ，功率显示 等-ATmega16 control intelligent motor controller 2-way high-current detection, load state control, power display
motor_control
- PID控制电机，控制电机在不同负载的情况下，保持电机恒速转动！-PID control motor, the motor control in the case of the type of load to maintain constant speed rotation of the motor!
VHDL-book3
- D_flipflop：1位D触发器的设计 D_fllipflop_behav：4位D触发器的设计 reg1bit：1位寄存器设计 reg4bit：4位寄存器设计 shiftreg4：一般移位寄存器的设计 ring_shiftreg4：环型移位寄存器的设计 debounce4：消抖电路的设计 clock_pulse：时钟脉冲电路的设计 count3bit_gate：3位计数器的设计 count3bit_behav：3位计数器的设计 mo
oriented_vector_control
- 异步电机间接矢量控制Simulink仿真模型，带有转速外环和Iq、Id两个内环，转速和负载指令阶跃变化，3/2变换为恒幅值变换，不包含弱磁控制，磁链指令为恒值。PWM调制算法采用空间矢量调制（SVPWM）。 -Indirect induction motor vector control Simulink simulation model with speed outer and Iq, Id two inner ring speed and load instructions step c
indirectfuzzyaddednewimadded
- in-direct torque control of induction motor using fuzzy logic. output torque is having less ripples and spees is constant, even torque changes from full load postive to negative
wuzuniraozu
- 三相同步电机系统dqo系统空载建立电压无阻尼绕组的仿真-Three-phase synchronous motor system dqo system load voltage without damper winding build simulation
cycloconverter
- it is single phase cycloconverter used in many ways to control the frequency or rather would say reduce the frequency to control the speed of motor but here iam using only resistive load because my teacher only give me this project. To use simulink
laosyjmain
- 一种单片机控制载荷疲劳试验的C51程序（包栝7段数码管动态显示程序，键盘输入，次数和强度和保持时间输入，马达控制）-A single-chip control of the C51 load fatigue test program (including dynamic Trichosanthes 7-segment display program, keyboard input, frequency and intensity and the hold time input, motor co
Xiangkong
- 这是一个交流异步电动机相控节电器程序。具备了电机软启动功能和负载跟踪节能功能的程序。-This is an AC asynchronous motor phase controlled saver program. The motor soft start function and load tracking energy-saving function procedures.
UDPixel22
- The paper presents the concept and principle of operation. It establishes guidelines for designing the autotransformer. A simple model is developed and simulated to investigate the concept. Finally, the paper presents experimental results obtained fr
Monte
- 随机潮流计算，采用蒙特卡洛法进行潮流计算，负荷和风电机采用正态分布-Stochastic power flow calculation, flow calculation by the Monte Carlo method, load and wind motor using normal distribution
PMSM
- 这个是永磁同步电机矢量控制系统仿真，仿真结果正确，可以在空载、加载下很好的跟踪转速给定值。-This is a permanent magnet synchronous motor vector control system simulation, simulation results are correct, you can no load, a very good track speed setpoint under load.
shunt
- Wound-field synchronous motors are well-known in industrial drives requiring constant speed irrespective of load. Separately controllable dc excitation in the form of dc field current is a unique feature in the power factor control of such a
MATLAB-simulink
- 直流电机调速的MATLAB仿真（开环闭环加矫正不加矫正）simulink模型，空载以及有负载的仿真实例。MATLAB simulation of DC motor speed control (open-loop closed-loop plus correction without correction) simulink model, simulation examples, and there are loads of load.-MATLAB simulation of DC motor
bujindianji
- 步进电机是将电脉冲信号转变为角位移或线位移的开环控制元件。在非超载的情况下，电机的转速、停止的位置只取决于脉冲信号的频率和脉冲数，而不受负载变化的影响，即给电机加一个脉冲信号，电机则转过一个步距角。-Stepper motor is the electrical pulse signal into angular displacement or line open loop control elements of displacement.In the case of the overload,
power_battery
- 电池与一个动态的50A负荷相连，当SOC低于0.4时，启动同步电机转动，给电池充电；当大于0.8时，停止同步电机转动。-The battery is connected to a constant load of 50 Amps. The DC machine is connected in parallel with the load and operates at no load torque. When the State-Of-Charge (SOC) of the battery go