搜索资源列表
FlashProgramTool
- After the single transaction waveforms are implemented in the GPIF Designer, the next step is to integrate the USB portion of the overlying firmware with the GPIF Designer output to perform write and read operations to and from the external FIFO. T
cmos_fifo_usb
- cmos数据到fifo再到usb的fifo部分程序(68013a)
Slave_FIFO_ep2out_16bit
- 用Keil C语言编写的EZ-USB CyC768013芯片 slave FIFO模式的固件程序
18
- 程式描述：使用Cypress的Cy7C68013A晶片進行設計，實現Slave FIFO模式的資料獲取。程式包括USB韌體程式以及主機程式。 安裝：把來源程式碼複製到硬碟特定目錄下，使用Keil C編譯器和Visual C++ 6.0運行即可。 注意：可以首先使用Cypress的測試工具進行韌體程式的測試，以確保韌體程式的正確性。 -Program Descr iption: Using Cypress
ft245_driver-lin26-203
- ft245 usb->fifo 芯片在LINUX2.6内核下的驱动源代码。可用于主机和外部设备如单片机的快速数据传输。-this is the device driver for ft245 chip under kernel linux2.6 you can exchange data with external embeded system easily through ft245.
EZUSB_Bulk
- USB_BLUK例程，BLUK传输模式，是配合cypress公司EZ_USB FX2系列芯片的源码-USB_BLUK routine, BLUK transmission mode, is in line with cypress company EZ_USB FX2 series chips source
GPIF_FIFO_Transactions_Auto_mode
- USB的GPIF中FIFO传输方式的例子-keyword: cypress USB GPIF fifo
2270B_USB_Library_ISP_m_V2.0
- USB的HID固件程序，单片机开发 Bus_Reset: ------------------------------------------------------------------ into Normal Mode, two NOPs are required. ------------------------------------------------------------------ b0bclr FSTPHX nop nop
DEC6416_USB
- 基于ti 6416芯片 程序包括 C6416 对USB 寄存器的读写，配置 以及FIFO，setup包 和 Endpoint（）的相关操作-Ti 6416 chipset-based procedures, including C6416 to read and write registers on the USB, configuration, and FIFO, setup package and Endpoint () of the related operations
USB_firmware
- Cypress USB芯片8051固件程序，sync fifo模式，C开发-8051 Cypress USB chip firmware, sync fifo mode, C development
SlaveFIFO
- usb大全，第十八章实现slave FIFO数据传输的上位机程序源代码-usb Daquan, Chapter XVIII achieve slave FIFO data transfer PC source code
Keil
- USB大全第十八章实现slave FIFO的外部控制器程序-USB slave FIFO Daquan Chapter XVIII of the external controller to achieve program
FIFOGJ
- USB大全第十八章实现slave FIFO数据传输的固件程序源代码-Chapter XVIII Daquan USB slave FIFO data transfer to achieve the firmware source code
Bulkloop
- USB固件初始化，实现FIFO模式下地数据传输-USB firmware initialization to achieve data transfer FIFO mode Shimoji
USBDataAcquire_Instance
- 在CY68013的FIFO模式下实现FPGA从USB中获取数据-In CY68013 the FIFO mode the FPGA to get data from the USB
USB_FPGA
- 基于Cyclone EP3C25的USB与CY60183传递数据的FIFO Verilog HDL源代码（FPGA端程序）-The program is a communication source code about USBCyclone EP3C25 transfering data via FIFO with CY60183 (only FPGA source code(verilog HDL) is included)
usb1_funct_latest.tar
- USB 1.1 slave/device IP core. Default configuration is 6 endpoints: 1 Control, 1 Isochronous IN, 1, Isochronous Out, 1 Bulk IN, 1 Bulk Out, 1 Interrupt IN. Includes control engine, providing full enumeration process in hardware - no external mi
Apptest
- USB2.0 接收FIFO数据，下位机是CYC68013-USB 2.0 receive FIFO data
EbbulkloopZ
- EZ-USB FX2 SLAVE FIFO模式固件代码-EZ-USBB FX2 SLAVE FIFO mode firmware code -EZ-USB FX2 SLAVE FIFO mode firmware the code-EZ-USBB FX2 SLAVE FIFO mode firmware code
USB_Control_Firmware
- C++语言编写的针对CY7C68013A芯片的固件程序。包括了对USB Slave FIFO的配置和内部传输管道以及FIFO大小的必要控制。该程序在硬件上通过测试，在没有其他USB设备干扰的应用下，可以确保450Mbps通讯效率。-Firmware control for USB Slave FIFO in CY7C68013A. It define the necessary configuration on transaction segment and pipe as well as FI