搜索资源列表
cktx1
- 将程序编译通过，写入芯片，插入实验板，用通读电缆将实验板与主机的串口相连就可以实验了。上面的程序功能很简单，就是每隔一段时间向主机轮流送数55H和AAH，并把主机送去的数送到P1口。-procedures to compile and write chip, insert experimental boards, reading the cable will be used experimental plate and serial port connected to the mainframe
串行接口通讯实验代码
- 串行接口通讯试验该试验可以学习如何编写一个通讯程序。这个试验能够实现的功能很简单，仅仅作为试验用。工作环境为：无需其余任何环境，直接接通电源即可。-serial communication interface test of the pilot can learn how to prepare a communication process. The pilot function can be achieved is very simple, just to experiment with. T
iic AT24C08的单字节读，单字节写，页读和页写
- 我实验的是 AT24C08的单字节读，单字节写，页读和页写，在高于3.3V系统中他的通信速率最高400KHZ的，我实验里用的是100KHZ的速率-My experiment is AT24C08 single-byte read, single-byte write, page read and write page, above the 3.3V system, the highest rate of his communications 400KHZ, I experiment with t
vb
- 1．Prodave 是用于pc 与s7 系列plc 之间的数据链接通信的工具箱。其实质就是用户通过调用“w95_s7.dll”等库函数来解决 PLC 与PC之间的数据交换和数据处理问题。 所需硬件为：CPU22x,PC/PPI编程电缆，带COM口的PC。这可能是最简单的配置，很容易实现试验的目的。这里不需要安装Prodave软件，只要把“w95_s7.dll”文件拷贝到您程序相应的目录中去即可。 2．通讯设置：打开“控制面板”中“设置PG/PC接口”选项，在“应用程序访问点”列表框内选择“S
RS232
- RS232串口通信实验，实现计算机和单片机之间的通信-RS232 serial communication experiment, the realization of single-chip computer and communication between
RS232CommunicationExperiment
- RS232通信实验源代码，发送端和接收端通过串口（RS232标准）实现通信-RS232 communication experiment source code, the sending end and receiving end through the serial port (RS232 standard) implementation of communication
uart
- verilog写的与电脑通信的uart，我实验过了，一切都很好，工作很好-verilog written communication and computer uart, I had the experiment, everything is very good, very good work
UART_rec
- fpga 串口通信 本程序在fpga开发板上实验成功-fpga serial communication program in fpga development board in this experiment was a success
ourdev_187634
- fpga 串口通信 本程序在fpga开发板上实验成功-fpga serial communication program in fpga development board in this experiment was a success
serial
- 网络上好用的串口工具的一个集合,可以做为实验与教学和开发的辅助.各有各的特点,请根据需要选用.-Useful tool for the network as a set of serial port, you can experiment with the teaching and development as complementary. Each have their own characteristics, follow the need to use.
CommAssistant
- VC编写的串口调试助手,功能齐全,性能稳定,实验多次,大家放心用吧-VC prepared by serial debugging assistant, functional, stable performance, experiment many times, we rest assured it
Manyserialcommunicationtest
- 实验名称：多机串口通信测试 试验功能：通过单片机发送数据给PC机, 通过串口调试助手（设定为字符格式显示）显示发送的数据 -Experimental name: serial communication function: through the experiment test data sent to chip PC, through a serial port debug assistant (set) showed that character format for sending dat
6
- 串口通讯实验： 本实验得到的结果为，打开超级终端，设置波特率为115200，数据流控制位为无。运行系统，就会显示“UART & Interrupt Experiment,Please Input from the keyboard”，我们就可以通过写串口操作。 在flash调试时，需要修改RO BASE为0x00000000，其他不用修改，重新编译下载就可运行。 注意：由于系统产生中断，程序计数器就会跳到0x18处执行中断服务子程序，所以不能在SDRAM调试。 -Ser
chuankou
- 简单的串口调试，可用于串口通信的初学者学习实验，数码管管采用共阳极。-Simple, and can be used for the serial adjustment of serial communication, digital beginners experiment of tube using anode.
8250
- 微机原理实验+PC机串行通讯8250，word格式的报告-Computer principle experiment+ PC serial communication 8250
AT24C02I2C
- AT24C02的I2C实验.此实验为AT2402实验。从地址0x80开始写入0到9，然后再从AT24C02中读入，把读取的数据 发往串口。-The I2C AT24C02 experiment. This experiment AT2402 experiments. Starting from address 0x80 write 0 to 9, and then reads from the AT24C02 to read data sent to the serial port.
Serial-debugging-assistant
- 串口调试助手，应用于串口调试实验，简单实用-Serial debugging assistant, used the serial debugging experiment, simple and practical
Counter
- 程序说明:本程序是将串口接收到的数据中的A的个数进行计算，显示结果 硬件连接:使用实验箱BACK 3部分电路。-Program Descr iption: This program is the serial received data to calculate the number of A, showing the results of hardware connection: using part of the circuit experiment box BACK 3.
ourdev_611558KA2KDJ
- ALIENTEK MINISTM32 实验3 串口实验-ALIENTEK MINISTM32 Serial Experiments Experiment 3
I2C
- I2C串口调试代码，包括I2C主机实验－读写CAT1025，I2C从机实验－CAT1025器件模拟。-I2C serial debugging code, including I2C host experiment- read and write CAT1025, I2C slave test-CAT1025 device simulation.