搜索资源列表
USB LED输出示例
- some examples of LED display vir EZUSB
usb061
- 基于凌阳SPCE061A芯片的USB通讯可实现1.通过USB通讯,PC端应用程序能够控制LED灯的亮灭;2.PC端应用程序发送小于65字节的字符串给SPCE061A,SPCE061A接收PC发送的小于65字节字符串后将接收到的字符串发送给PC,PC接收字符并显示在界面。-based Sunplus SPCE061A USB chip can achieve a communication. USB communications, PC-side applications to control t
EZ-USB HID Keyboard
- This Program uses the 2131 dev board s push buttons and seven-segment LED for limited keyboard functionality and is based on the EZ-USB firmware frameworks.
ApplicationControlLED
- 内有usb固件程序与上位机程序,通过上位机操作控制LED灯的显示-There are usb firmware and PC programs, operational control by the upper LED light display
42pcb
- 该工程是一个FPGA的开发板 主要包括了FPGA芯片:EP3C25Q240C8 FPGA的配置芯片采用:EPCS16 USB芯片:CY7C68013A USB的FLASH采用:24LC64 AD芯片:AD9238 电源部分:LMS1117-3.3两块分别对USB、模拟部分和FPGA供电;LMS1117-1.2为FPGA核心电压;LMS1117-2.5为 IO口及PLL供电 9盏LED,4个开关 主要完成的一个功能是高速模拟信号的采集,以及上位机传输
pdiusbd12
- PDIUSBD12固件编程简单实例,USB设备配置后,使与P1口连接的LED全亮-PDIUSBD12 s easy firmware programming example, the LED lights that are connected with P1-wide will be lighted after usb device is configurated.
HostLEDcontrolprocedures
- 上位机控制LED程序,在KEIL中运行,适用于CYUSB的开发和仿真-Host LED control procedures, in KEIL run for the development and simulation CYUSB
USBkey
- 用单片机做的USB开发板的键盘程序 开发板上共有8个按键,功能分别为: K1:左Ctrl键 K2:左Shift键 K3:左Alt键 K4:0键 K5:1键 K6:2键 K7:Caps Lock键 K8:Num Lock键 按键功能测试: 同时按下K1和K2可做输入法切换,这跟键盘上的两个键功能一样的。 K7可打开大写字母锁定,同时LED2亮起。K8是小数字键盘锁定键, 当数字键盘打开时,LED1亮起,这时可用K4,K5,K6输入数字。 请留意EDN板
C_Example_LED_Blink
- CY6308的LED使用例程。CY对LED的集成支持也很不错。-CY6308 routine use of the LED. CY on the LED integration support is also very good.
sh86312_PP
- 车载MP3方案 FM+AM+SD +USB+ WMA+ MP3 +2313+ AMP -CAR MP3 SOLUTION WMA MP3 FM AM 2313 4730 4702 LCD LED
cy68013a_led
- 通过计算机上位机发送指令控制CY68013AUSB开发板的LED.-Host computer to send commands through the computer control CY68013AUSB development board LED.
USBLED
- 使用VC++2008开发的基于对话框的控制cy68013a开发板LED显示的工程文件。-Developed using VC++2008 dialog-based control cy68013a development board LED display project file.
USBLED
- USB控制LED显示实例,把源码拷贝到某个目录下,并在相应的编译环境中打开即可。 -USB controlled LED display examples, the source copy to a directory and open the appropriate build environment can be.
FS2410_APP
- 优龙FS2410开发板(ARM920T核)非操作系统下的外围硬件测试程序,包括音频、LCD、LED、蜂鸣器、按键、串口、网口、USB等测试程序。-EURONAVY FS2410 Development Board (ARM920T core) non-peripheral hardware, operating system testing procedures, including audio, LCD, LED, buzzer, keypad, serial port, network po
EZUSB_USBLED
- 用CYPRESS的cy7c63813驱动LED,USB学习入门教程 -CYPRESS the cy7c63813 drive with LED, USB Learning Tutorial
USB_Ref
- USB control LED using Jungo Windriver
WR_CtrlLED
- USB控制LED灯的程序 包括USB设备的数据收发灯-USB LED light control procedures, including USB devices for data transmission light
the-test-about-USB-light-up-LED
- 一个通过USB端口去控制LED灯亮的MFC软件-A MFC software that can control LED lighter through USB port
SourceCode
- 实现自定义的USB编程。启用了D12的端 点1和端点2,端点1为中断传输,最大包为16字节,查询间隔为10ms。端点2为批量 传输,最大包为64字节。端点1的输出第一个字节为控制END USB板上的LED的,每个 bit代表一个LED,为1时表示对应的LED亮。端点1的输入第一个字节为返回的开关 状态,每个bit代表一个按键,为时表示对应的按键按下。输出端点2的数据通过串 口发送出去,串口接收到的数据通过端点2返回。-Implement custom USB programm
led
- 使用型号为CY7C68013A的USB芯片,通过开发板上的按钮控制LED灯的状态-This directory contains the dev_io 8051 firmware The purpose of this software is to demonstrate how to use the buttons and LED on the EZ-USB developer s kit. The device I/O example program uses