搜索资源列表
51读写U盘源程序和原理图
- 这是51读写U盘源程序和原理图,希望对开发USB的兄弟一些参考.-Source code for USB mass storage read/write with descr iption.
NAND FLASH的读写程序
- Nand flash 读写程序 C语言代码，可以给U盘开发者参考 可以读写三星各种型号的Nand flash芯片-NAND flash reader C-language code, for U-reference developers can read and write various models of Samsung's NAND flash chips
liu616
- 单片机＋sl811hs读写u盘的代码，包括底层驱动，fat16文件系统-Single chip and s1811hs source code for USB mass storage read/write, including lower level code and FAT 16 file system.
基于ADU812+PDIUSBD12的数据采集板源代码
- 基于ADU812+PDIUSBD12的数据采集板源代码发布！这一回是用C写的！！！！！强烈推荐-ADU812 PDIUSBD12 based data acquisition boards source code release! This is used to write C! ! ! ! ! Strongly recommended!
USBOOT
- 1.增加写保护跳过对话框，允许用户跳过写保护提示 2.增加备份和恢复磁盘的功能，类似克隆 3.可自定制启动文件包 -1. Write to increase protection skip dialog that allows users to skip write protection suggest two. Increased disk backup and restore functions, similar cloning 3. Since the start can be
readwriteudisk
- based on lpc2210 and isp1161, usb host, read and write u disk. from zlg-based on lpc2210 and isp1161, USB host, u read and write disk. from zlg
firm_usb
- DSP通过双口RAM和ISP1581实现下位机的USB固件程序，调试通过，上位机驱动和读写例程，如果下载多的话再传-DSP through dual-port RAM and ISP 1581 to achieve lower computer's USB firmware and Debugging, PC drivers and routines to read and write, if you download are so tame
200652622134161862
- 程序为D12的USB测试程序 main.c为主程序 D12.c为PDIUSBD12芯片操作子程序 usb,c为usb协议部分 isr.c为中断处理程序 包括定时器中断（没用）/INT0中断（单片机INT0脚与PDIUSBD12中断脚相连） hard.c为硬件底层程序，读写端口 mydev.c为我的设备请求程序-procedures for the testing procedure main.c USB mainly procedure
51+sl811
- 51+sl811读写U盘的源程序 -51 sl811 U disk read and write the source code reader 51 sl811 the U-source
FX2GPIFSingle-Burstdatareadwrite
- EZ-USB FX2的一个单字读和单字写的程序，利用GPIF轻松实现，值得一看-EZ-USB FX2 in a word read and write words of procedure, and use GPIF easily, an eye-catcher
zhyg_ezusb
- 汇编语言写的ez-usb fx2 固件程序传输带宽480M/S-assembly language to write the ez-usb accordance firmware transmission bandwidth of 480 / S
mcu_CH375
- 该程序用以通过单片机来控制芯片CH375 实现对海量存储器的读写操作-procedure for the adoption of the single-chip microcomputer to control chip to achieve CH375 Massive Memory read and write operation
HIDInterface
- This module is common to all of the Example programs It declares the {Open, Read, Write, Close} calls for the USB device These user-calls are translated into OS system calls This module also contains several support routines used by all of
怎样编写一个在USB接口读写数据的程序
- 怎样编写一个在USB接口读写数据的程序-how to Write/Read USB port ?
usb_programm
- 用USB控制硬硬盘读写的汇编代码。-control with USB hard drives read and write assembly code.
usbhidio_vc6
- USB HID read write in VC6
usb_paul
- usb bulk read and write with libusb lib, it is a useful lib,it is great
CY7c68013_fpga_write_sram
- FPGA自FX2 slavefifo中读取数据，写入至SRAM-FPGA since FX2 slavefifo read data, write to the SRAM
MicroUSB_How+to+write+a+USB+Driver
- How to write a USB HID driver
usb372-read-and-write
- usb372 read and write.vi.实现了usb与labview的通信-usb372 read and write.vi