搜索资源列表
定时器1
- ;T0为0.1秒计时,T1为外部中断计数,根据中断次数实现1秒的计时时间, ;然后控制P17以1秒为周期翻转。 ;P17接LED,P10接T1脚
stm8l152-tim4 基于STM8L的定时器TIM4 完成对LED灯的定时功能
- 基于STM8L的定时器TIM4 完成对LED灯的定时功能-Based on the Timer TIM4 STM8L complete timing LED lights
TMS320VC5509A_examples.TMS320VC5509A学习板例程及说明
- 这是一款TMS320VC5509A学习板例程及说明,里面包含很多例子,包括CPU看门狗实验、LED跑马灯实验、CPU TIMER定时器实验、实时时钟实验、AD转换实验、ADDR转为GPIO试验、蜂鸣器试验、GPIO试验、数码管显示试验、扩展SDRAM读写实验、SPI EEPROM读写实验、FFT实验、FIR滤波器实验、IIR滤波器实验、自适应滤波器实验、键盘扫描实验、外部中断输入实验、AIC23播音实验、1602显示试验、12864显示实验、240128显示实验、USB2.0通信实验等22个实验
AT89C51单片机编程定时器控制数码管动管显示
- AT89C51单片机编程定时器控制数码管动管显示,附带protuse仿真-AT89C51 Microcontroller Programmer timer control digital dynamic LED display, with protuse simulation
a0
- 利用定时器中断,每隔一秒,循环点亮LED灯。-Use timer interrupt every second, recycling lit LED lights.
led
- ARM LPC2200 定时器中断使用LED闪烁实验-ARM LPC2200 timer LED flashes interrupt the use of experimental
51kaifaban
- 51单片机全套学习资料 提供电路原理图 各种C语言实验程序 包括LED流水灯,数码管显示,中断,定时器,串口通信,DS18B20温度显示,液晶1602,12864显示,看门狗,按键检测,音乐播放等程序.-51 Singlechip a full set of learning materials to provide a variety of circuit schematics C language experimental procedures, including water LED li
led
- led显示程序,通过定时器中断,可以动态显示数字在数码管上。-led display program, through the timer interrupt, you can dynamically display the figure in the digital control on.
led-int
- 利用单片机的定时器以及中断的方法的LED灯显示程序。-The use of single-chip timer and the method of interruption of LED lights display program.
led(10-1)
- DSPF2812学习程序: 描述:利用GP定时器1在GPIOF8引脚上产生方波,令一个贴片LED闪烁 系统时钟150M,高速外设时钟25M,128分频后定时器周期为5.12us,适于初学者学习-DSPF2812 learning process: Descr iption: Using the GP Timer 1 GPIOF8 pin to generate a square wave, so that a flashing LED chip system clock 150M, high
intinterft
- AVR定时器功能 定时器每秒加一,0到255循环,通过数码管显示计数值-AVR timer function Timer per second, plus one, 0 to 255 cycles, through the LED display counts
led-pwm
- PWM 控制 LED 灯渐亮渐灭程序 适用 ME300B 开发系统 晶振为11.0592M 利用定时器控制产生占空比可变的 PWM 波 按K1,PWM值增加,则占空比减小,LED 灯渐暗。 按K2,PWM值减小,则占空比增加,LED 灯渐亮。 当PWM值增加到最大值或减小到最小值时,蜂鸣器将报警。-PWM control of LED lights getting brighter gradually eliminate procedures apply M
led
- 基本上程序还是DEMO程序,程序并没有采用定时器来生成PWM,而是采用延时循环来实现,这样就做不了其他事情 了,但实际上只需要将主循环转换为定时器中断处理即可,很简单.这个是参照市面上邦定IC RGB控制功能来做的,这应该是采用单片机方案最便宜版本之一了 -Basically the procedure or DEMO program, the program does not use a timer to generate the PWM, instead of using the de
TIMER_32BITS
- 定时器被设置为每秒产生两次中断,每个中断都 翻转一次相应的GPIO口,同时LED指示灯指示每次中断-Timer is set to generate two interrupts per second, each interruption is flip a corresponding GPIO port, while LED light indicates each interrupt
led
- 定时器中断的例程,实现一秒定时,并在led灯上显示- Writes routine which a timer interrupts, realizes one second fixed time, and demonstrated on the led lamp
STM8S内部时钟+定时器+LED
- STM8S的裸机模板,不使用库函数,包含基本外设配置,内部时钟配置、定时器配置、普通IO配置、LCD12864的驱动(STM8S bare metal template, without the use of library functions, including basic peripheral configuration, drive internal clock timer configuration, common configuration, IO configuration, LC
用定时器控制指示灯
- 此程序是nrf52832系统的小程序,作用是用LED显示定时器运行状态。(This program is a small program nrf52832 system, the role is to use LED to display the timer running state.)
定时_计数器
- 利用定时器和计数器,实现LED不同状态的变化(The use of timers and counters to achieve LED changes in different states)
STM32定时器中断程序
- 本源代码为讲解基于STM32的定时器中断程序,通过定时器TIM3产生间隔1秒钟一次的中断,在中断中控制LED发光二极管,每次中断都使发光二极管状态取反(This source code is explained based on the STM32 timer interrupt program, through the timer TIM3 interrupt an interval of 1 second, in the interrupt control LED light-emittin
定时器中断函数—库函数版本
- 使用定时器来控制两个LED交替闪烁 亲测可用(Use timer to control two LED alternately flashing pro test available.)