搜索资源列表
cc2430
- 1.点亮LED灯 2.按键控制 3.外部中断(按键) 4.单片机串口发送数据 5.定时器1 6.ADC单次采样-1 lit LED lights 2. Button control 3 external interrupt (button) 4. Microcontroller serial port to send data 5. Timer 1 6.ADC single sampling
electronic-clock
- 内容:DS1302实时时钟数码管显示,时间和日期切换显示 按下按键,循环切换 通过串口调试软件,打开串口,波特率默认9600,点击更新时间即可,如果不行,按下开发板复位重新更新-Content: DS1302 real time clock digital display, time and date press the button to switch the display to toggle the time seconds format debugging software t
dingshishizhong
- 综合运用51单片机知识设计一个可以随意调节时间、带整点闹铃的时钟。(其中用到定时器、中断、按键、蜂鸣器、数码管或串口通信)-51 monolithic integrated circuits design integrated use knowledge to control at the time, the alarm clock on the hour. ( use of the timer, and buttons, the buzzer, digital or serial commun
S8_test
- 本程序用来测试开发板上所有的设备。 1、VGA输出8位色彩的条纹; 2、PS/2键盘输入字符可以传输到LCD和串口调试终端上; 4、拨码与按键开关与4位LED相连-The procedure used to test all the equipment development board. 1, VGA output 8-bit color stripes 2, PS/2 keyboard input characters can be transmitted to the LCD
S7_PS2_RS232
- 本实验实现PS/2接口与RS-232接口的数据传输, PS/2键盘上按下按键,可以通过RS-232自动传送到主机的串口调试终端上(sscom32.exe); 并在数据接收区显示接收到的字符。 串口调试终端的设置:波特率115200,一个停止位,无校验位。 -The experimental realization of PS/2 interface and RS-232 interface, data transmission, PS/2 keyboard, press the
WTV020-C51
- WTV020一线串口和三线串口控制C51代码。WTV010/WTV020是一款功能强大的一次性可编程语音芯片,音频输出为PWM或DAC模式。可选控制方式有按键控制模式、并口控制模式、串口控制模式等。-WTV020 line and three-wire serial control port C51 code. WTV010/WTV020 is a powerful one-time programmable voice chip, PWM or DAC audio output mode. O
CAN03
- 使用说明: 首先通过串口将“接收”“发送”程序分别下载到两个CAN开发板里面。下 载成功后,将继电器上面的6PIN排针换一下,上面两针分别竖着端接在一 起。并将485对应的端子A---A,B---B连接在一起。 现象: 按发送机的按键,接收机的LED灯做二进制加法显示。连接方法见图片。-Instructions for use: First, through the serial port will " receive" the " send&quo
keypad
- 4*4点阵键盘的实现。用运反转扫描法来实现对键盘的扫描,确定是那个按键接通,并通过串口输出,显示在显示器上。-4* 4 matrix keyboard implementation. Scanning method used to achieve the reverse operation to the keyboard scan to determine that the button is switched on, and through the serial output, display
the-keys
- 按键发送数据程序,四个按键,依次通过串口发送16进制的80,81,82,83-the keys
tongxin
- 利用串口通信MAX232形成多机通信的交通管制,正常状态,2从机自动几秒红绿交替,主机显示各个情况,特殊情况,主机按键1,2,3,4各控制从机红绿,5让从机正常工作,6,7改变波特率,按键由PCF8574做的4*4,带实验报告,原理图.-Formed using serial communication MAX232 multi-machine communication traffic control, normal, 2 seconds from the automatic alternat
frowardboard
- 基于STC11F-10Fxx实现按键扫描以及串口通信系统-Push-based STC11F-10Fxx scanning and serial communication system
UCOSstart-Key
- 这是UCOS在ARM7上的按键仿真(proteus),自己测试完全可以实现,比如用一个发送"按钮”启动LED闪烁或者串口任务。-This is UCOS ARM7 buttons in the simulation (proteus), his test completely realized, such as using a send "button" to start LED flash or serial task.
jianpanuart
- 键盘按键控制串口发送,按下按键立即发送字符,松开停止发送-keyboard control uart send
MsW
- lcdkeyuarc201 04:基于C51的按键操作,12864液晶显示,串口通信三模块开发的控制器程序。-lcdkeyuarc20120104: key operation based on the C51, 12864 liquid crystal display, serial communication controller three-module program development
kinetis10epwm
- 飞思卡尔armcortexm4 kinetis10的pwm产生源码程序,使用串口通信,按键改变占空比。-the example of kinetis10 epwm.
STM32Pkey-PWM-outPUART
- 基于CORTEX M3 STM32 的按键调控PWM输出和串口输出占空比的程序-STM32 PWM OUTPUT and UART
stm32-key-44
- STM32F103系列 44按键中断、扫描 串口输出-STM32F103 series 44 Key interrupt, scan Serial output...
ledPinterrupt
- 在友善之臂的代码基础上进行了修改:能够产生中断,按键1按下时,led1和4亮;按下按键2,led2和3亮,同时在串口显示哪个键按下了。 解决中断在SDARM中不能进行的原因。-S3C2440 led interrupt
nfrared-communication
- 红外通信:红外与串口通信的应用,红外遥控按键-Infrared communication: infrared and serial applications...
display
- 热泵空调的显示板程序,包括液晶驱动,按键响应,串口通讯等程序代码。-Heat pump display board procedures, including LCD driver, key response, serial communications code.