搜索资源列表
diansai
- 2012年电子电路设计大赛小车程序,完美跑完全程-2012 Electronic Circuit Design Competition car program, the perfect finish the course
radiogram
- 做电子电路实验时,会要焊收音机,这个是收音机的电路图。-The electronic circuit experiment, it will be welded radio, this is the radio circuit.
pyroelectric-alarm-circuit
- 包括两部分,一部分是Proteus软件对一些典型的数字电子电路进行仿真,包括555计数器,555发生器,555触摸延时开关设计,74ls138译码器逻辑状态显示等。另一部分是单片机控制的热释电报警电路实现程序。-Proteus software to simulate typical digital electronic circuits, including the 555 counters, 555 generators, 555 Touch delay switch design 74ls
temperature-control-circuit
- 包括两部分内容,一部分是Proteus仿真软件对模拟电子电路进行仿真,包括基本互补电路、共射放大电路、集成运算放大电路等,另一部分是温度控制电路。该设计以STC89C52单片机为主控元件,以DS18B20为温度传感器,可以实时检测温度,并把范围内的温度显示在LED数码管上- using Proteus software simulates analog electronic circuits, which includes the basic complementary circuit, com
EMI_reference
- EMI电磁干扰屏蔽方法,设计大型电子电路时减少EMI的经典方法,电路设计参考必备-EMI electromagnetic interference shielding method, large-scale electronic circuits designed to reduce EMI' s classical method, the essential reference circuit design
YX_YKSCH
- 关于电力自动化远动产品谣信、遥控的电路原理图,对学习电子电路的人很有帮助-automation of remote power products Bellflower letter, remote control circuit diagram for the study of electronic circuits helpful
HY-SRF05
- 超声波测距模块的介绍,电子电路原理图和程序代码-Introduction ultrasonic ranging module, electronic circuit schematics and program code
temp
- 运用所学的数字逻辑电路、模拟电子电路、单片机、测控电路等的基本知识,设计并制作一个非接触式红外线测温仪。该系统以单片机为核心,外接其他外围电路组成。-Use of digital logic circuits, analog electronic circuit, single chip microcomputer, measurement and control circuit of the basic knowledge, such as the design and constructio
VHDL代码
- 实现简单的电子拔河比赛,即两按键模拟,计数器计数,比较器进行比较,最后通过LED灯进行直观显示(To achieve a simple tug of war competition, that is, two button analog, counter count, comparator comparison, and finally through the LED lamp for visual display)
boost
- boost电路拓扑,电力电子技术整流电路拓扑(Boost circuit topology)
danpianji
- . 应用MCS-51单片机设计电子秒表电路; 2. 选用4位LED数码显示,计数时间0-9999s,定时时间可调; 3. 硬件设计根据设计的任务选定合适的单片机,根据控制对象设计接口电路。设计的单元电路必须有工作原理,器件的作用,分析和计算过程; 4. 软件设计根据电路工作过程,画出软件流程图,根据流程图编写相应的程序,进行调试并打印程序清单; 5. 原理图设计根据所确定的设计电路,利用Protel等有关工具软件绘制电路原理图、PCB板图、(Design of electronic st
71477215HY-SRF05
- HY-SRF05 模块资料 超声波测距模块的介绍,电子电路原理图和程序代码(Introduction ultrasonic ranging module, electronic circuit schematics and program code)
多种波形产生电路
- 波形产生器 原2015年全国大学生电子设计竞赛综合测评题(Waveform generator from The National Undergraduate Electronic Design Competition in 2015)
DaSai_20170808
- 系统以STM32单片机作为核心控制芯片,利用其内部的PCA模块产生SPWM信号,再通过脉冲分配电路、逆变功率驱动电路和LC串联滤波电路获得三相逆变器50Hz正弦波功率信号的输出。(System to STM32 microcontroller as the core control chip, SPWM signal generated by PCA module inside, and then through the output pulse distribution circuit, in
sch100317
- 本高压脉冲式电子围栏设计主要采用高频脉冲,进行开关式充放电使得磁环次级的电压升高,用4倍压电路再次升高电压,次电路可以得到5KV-10KV电压,是人的触感强烈,但是不会伤害人体。(The high voltage pulse type electronic fence design mainly adopts high frequency pulse, to switch type charging and discharging the circular and the secondary v
FreqSweep
- 此程序用于arduino板(nano,其他可适当修改引脚),MCU采集信号发生器的波形,然后再输出同等频率的互补方波,主要用于驱动全桥或半桥逆变电路,可作为电力电子电路驱动信号扫频。 信号发生器采集引脚:D4 输出方波引脚:D9和D10(This program is used for Arduino board(nano,also can be modified for other types). MCU collect waveform from signal generator,th
单片机电子时钟设计
- 单片微型计算机简称单片机,又称为微控制器,是将CPU、RAM、ROM、定时/计数器、I/O接口电路集成到一块电路芯片上构成的微型计算机。本次设计的系统由单片机系统、数码管显示系统、键盘、蜂鸣器等组成,通过按键来控制单片机实现数字时钟的时、分、秒显示,12、24制转换,设定时间、闹钟等不同功能,并通过P0口的输出在LED上显示。该设计具有结构简单、使用方便等特点。(As the single chip computer, also known as micro controller, CPU, R
1
- 基于汇编语言的电子密码锁(原理图、PCB、程序源码、仿真电路等)(Electronic code lock based on assembly language (schematic diagram, PCB, program source code, simulation circuit, etc.).)
1-2-28-光敏电阻ADC读取程序
- 当光线照射到光敏电阻上,并且光线强弱变化时,光敏电阻会跟随改变电阻的阻值。可以用于感光的电子电路上面。例如根据自然光线的强弱,自动开启或者关闭照明线路(When the light is irradiated to the photosensitive resistor and the intensity of the light changes, the photosensitive resistor will follow the resistance of the resistor. It
1-2-29-光敏和电位器ADC读取程序
- 当光线照射到光敏电阻上,并且光线强弱变化时,光敏电阻会跟随改变电阻的阻值。可以用于感光的电子电路上面。动开启或者关闭照明线路(When the light is irradiated to the photosensitive resistor and the intensity of the light changes, the photosensitive resistor will follow the resistance of the resistor. It can be used