搜索资源列表
E35G23_UCOS2_UcGUI
- 豪华板中E35G23的UCOS2+UcGUI图形系统2.76,UCOS_II测试程序说明,由hgxxx的ucosii2.71升级而来的!去掉了TaskLcd running显示,把这个任务作为GUI显示输出,类似于UCOS的例子1,在一个随机的位置显示一个随机数,只是允许一个任务调用GUI,没有显示cpu利用率、切换次数等信息!注意:~本程序适用于240×320 16级灰度液晶!去掉了TaskLcd running显示,把这个任务作为GUI显示输出,类似于UCOS的例子1, -luxury
LwIPPortingTest_6_1
- lwip1.1.1 + ucos2.76 for AT91SAM7X256 + RTL8201BL(PHY)-lwip1.1.1 ucos2.76 for AT91SAM7X256 RTL8 201BL (PHY)
AVR_M16_ucos_II
- 1. OS版本为2.76 2. 使用Timer0的比较匹配中断为系统定时,频率为100Hz 3. 三种临界代码保护方式均可以使用,在OS_CPU.h里直接设置即可 如果安装了WinAVR20050214,则直接运行start.bat,输入make all即可开始编译。 如果需要在AVRStudio仿真,运行make extcoff后即可生成调试所需的cof文件。-1. OS Version 2.76 2. Timer0 use of matching interruptio
uCOS-II2.76
- uCOSII 2[1].76商业版本源代码
320X240LCD仿真程序
- 320X240LCD仿真程序 320x240lcd仿真程序,仿真单色,4色,16色,256色lcd 使用方法:(需要注册mscomm32.ocx控件程序才能正常运行) 通过串口或TCP/IP将LCD显示缓冲区的全部内容发送到本软件接收即可 软件同时监控串口和tcp/ip口的数据,数据为一屏时刷新显示内容。 数据格式: 单色:unsigned char lcdbuf[9600] 每位一点 4色:unsigned char lcdbuf[19200] 每两位一点 16色:unsigned char
uCOS-II_Mage128
- 移植ucos2.76到mega128中软件仿真成功。 需要在iccavr7.13中编译,软件仿真AVR Studio 4.12。下载后将其解压到d下编译,否则可能要修改iccavr 的环境变量。就是菜单project下的Options选择paths进行设置。 -Transplantation ucos2.76 to mega128 success in software simulation. The need for compiling iccavr7.13, software simul
ucos276_S3C2400_ADS_1.2_release
- Target board specifications ~~~~~~~~~~~~~~~~~~~~~~~~~~~ CPU : Samsung S3C2400 (ARM920T core) ROM : HY29LV160 for internal boot ROM and HY29LV1024 for external boot ROM RAM : Samsung K4S281632 16MB(2M*16bit*4banks) SDRAM * 2EA Compiler :
10.1.1.76.6786
- Implementation of Single Precision Floating Point Square Root on FPGAs
Source-lwiptranslatenoteucosII-JHB
- 焦海波的lwip在ucosII的移植笔记及其源码,源码软件环境为:ADS 1.2,LWIP1.1.1,ucos2.76。硬件环境为ARM7-AT91SAM7X256,PHY为RTL8201BL。移植笔记的源码不好找,特此上传。-Jiao Haibo- the transplant notes of The lwip in ucosII. It s notes source. Software environment: ADS 1.2, LWIP1.1.1 ucos2.76. Hardware
USB-Composite-Device_6.1.7600.16385
- 一个在linux下的驱动文件,对应的型号是6.1.76-a device that can be used in linux,which is 6.1.76
infrared-receiver-principle
- 红外遥控器工作原理:红外线遥控就是利用波长为0.76~1.5μm之间的近红外线来传送控制信号的。-Infrared remote control works: infrared remote control signal is transmitted using near-infrared wavelength between 0.76 ~ 1.5μm.
LegM2-1.76-16.04.07
- ..6544444444454654654(HKHKJHGHJGJHGJKGHKJHGJ)