搜索资源列表
AD9244 (ADC)
- 用BF533的AD程序-BF533 with the procedures AD
vhdl程序例子
- vhdl程序源代码,包括Combinational Logic Counters Shift Registers Memory State Machines Registers Systems ADC and DAC Arithmetic等-VHDL source code, including Combinational Logic Counters Shift Registers State Machines Registers Memory S
Vmeter
- 在picdemo2实验板上的一款lcd+adc程序,由pa0测得电压,在lcd上显示,当电压值高过3.5v时,报警-picdemo2 experimental board in the new LCD celade procedures pa0 measured by the voltage, the LCD on, when voltage is higher than 3.5V, the Alarm
adc过采样
- 这是cygnal8051f020的读写adc的程序-literacy celade procedures
基础篇 21. STM32 ADC模拟量输入实验
- 原子的最基础的单通道、单次的采集初始程序。(The most basic single channel single sampling)
1.ADC-Serial
- STC12C5A60S2单片机P1口ADC模数转换程序,通过串行口输出到电脑终端监控,电脑终端发送“0”,返回第一通道转换值。(STC12C5A60S2 microcontroller P1 port ADC analog-to-digital conversion process, through the serial port output to the computer terminal monitoring, the computer terminal to send "0&q
ADC转换
- msp430f14916位单片机ADC程序源码(msp430f14916 one-chip ADC program source code)
C8051F310 ADC采样
- C8051F310 ADC采样程序.2. 功能:实现ADC采样芯片外的模拟电压,通过LCD显示,并通过串口(J6)发送到PC机 注:试验时把LCD电源跳线(J20_1和J20_2)联接好!(C8051F310 ADCconversion)
ADC+DMA
- stm32f407 adc配合DMA案例程序(stm32f407 adc case program)
ADC
- stm32F103 adc采样程序,包括初始化和配置等(u16 ADC_Get_aveg(u8 ch,u8 n) { u32 ad_sum = 0; u8 i; for(i=0;i<n;i++) { ad_sum += Get_val(ch); delay_ms(5); } return (ad_sum / n))
410驱动ADC0
- 实现C8051F410单片机的ADC功能,方便大家使用(The realization of the ADC function of C8051F410 single chip is convenient for everyone to use)
2.LCD-adc
- STMF407 液晶显示adc采样值,液晶接口在程序说明中,经过测试,绝对可以使用(Liquid crystal display ADC sampling value, liquid crystal interface in program descr iption, after testing, can be used absolutely)
ADC采集电压
- 通过ADC电压变化改变PWM波占空比的程序。(The program of changing the duty ratio of PWM wave through the change of ADC voltage.)
实验18 ADC实验
- 每隔 250ms 读取一次 ADC 通道 5 的值,并显示读到的 ADC 值(数字量),以及其转换成模拟量后的电压值。同时控制 LED0 闪烁,以提示程序正在运行。 这里关于最后的 ADC 值的显示我们说明一下,首先我们在液晶 固定位置显示了小数点,然后后面计算步骤中,先计算出整数部分在小数点前面显示,然后计 算出小数部分,在小数点后面显示。这样就在液晶上面显示转换结果的整数和小数部分。(ADC is read every 250ms. The value of channel 5,
5702Demo程序
- ADC,UART,INT,TIMEER,等外设功能的示例代码(ADC, UART, INT, TIMEER, and other peripheral function sample code)
28335 PWM启动AD程序
- EPWM波启动AD采样,包含中值滤波和SCI发送程序(EPWM waves start AD sampling)
STM32的ADC程序,已调试成功!
- 这是STM32的ADC数模转换程序,已调试成功!可以直接拿去用
ADC
- 针对stm32开发板的程序,硬件包括传感器、单片机和数码管,程序带有信号处理(ADC、计算等)功能与转换输出至数码管显示功能(For the program of STM32 development board, the hardware includes sensor, MCU and nixie tube. The program has the function of signal processing (ADC, calculation, etc.) and the function o
STC8A8K单片机ADC采集程序
- STC8A8K单片机12位ADC采集程序,通过串口发送采集数据