搜索资源列表
27-12个IO驱动8个共阴共阳数码管
- 通过单片机模拟数码管驱动，驱动数码管，节省成本(Analog digital drive through the microcontroller, drive digital tube, saving costs)
tlv5638
- tlv5638 IO口控制，输出任意电平(TLV5638 IO port control, output any level)
STM32 IO口模拟IIC接口程序
- 本程序基于stm32单片机 的io口模拟IIC,STM32单片机硬件复杂且不好用，使用本程序简洁明了。(This procedure is based on the STM32 microcontroller IO port analog IIC, STM32 microcontroller hardware complex and difficult to use, the use of this program is simple and clear.)
IOUSART
- PIC单片机io模拟串口19200的实现(PIC microcontroller IO analog serial communication program 19200)
DOUBLE_NANDFLASH_2.2ms
- IO模拟时序与NANDFLASH通讯。 读，写，擦除指令都OK。(IO communicate with NANDFLASH , lpc1788)
new_simulation
- 通过时钟使普通的IO口模拟UART串口通讯(Use Timer_A CCR1 hardware output modes and CCR0 SCCI data latch // to implement UART function @ 2400 baud. Software does not directly read and // write to RX and TX pins, instead proper use of output modes and SCCI data // la
usart
- 在stm32f103上实现带crc16校验的通过串口3控制IO口读写功能。已通过测试(In STM32F103 with CRC16 checksum, through the serial port 3 control IO port read and write function. Have passed the test)
IO输出-点亮1个LED灯方法
- 流水灯：IO输出，LCD点亮一个流水灯方法(LCD lights up a water lamp)
IO=shuchu
- 输入与输出IO接口的编程程序，使用编程，开发利用。(Input and output IO interface programming program, the use of programming, development and utilization.)
I2CTest_UseSoftI2CModule(PB0,PB1)
- 本程序实现了用TI LM3S系列单片机的IO端口接入I2C总线，可以实时监控总线上的变化与传输，并将I2C传输的内容，实时通过串口打印出来，可用于破解各种I2C通信协议，曾经用于解析PIC单片机之间的I2C通信，解决了串口实时打印的问题，采用FIFO，UART接受与发送均采用中断，并解决了FIFO中断深度等等问题。仅供参考。(This program is used to achieve the IO port access I2C bus by using TI LM3S Series MCU
stm32软件串口1.0
- 通过stm32 io口模拟串口,串口接收通过中断. 本代码会把发送给串口的数据,发送出来(Through the STM32 IO port, the serial port is received through the serial port, and the serial port is received through the interrupt. This code will send out the data sent to the serial port)
INTC-SWvector-VLE
- IO中断Demo程序，对初学者帮助很大，请放心下载使用。(IO interrupts the Demo program, which is very helpful for beginners)
SoftWareSerial
- STM32 IO模拟串口 发送接受 波特率9600(STM32 IO Analog serial port to send acceptance.)
15-模拟串口-超时接收完成
- STC15单片机IO模拟串口-超时接收完成(STC15 MCU IO analog serial port - timeout receiving completion)
IrSend_1227_normal-to-1227Ir
- 此代码为IO口模拟红外的发送程序，自己写的，很好用(The code is used for Ir send with mcu io, it's useful very much!)
3-IO口控制
- 51单片机实现 999秒倒计时IO控制程序(51 singlechip to implement a 999 second countdown IO control program)
STM32的IO模拟I2C主机_硬件I2C从机
- STM32 IO口模拟IIC(STM32 ads1115 STM32 ads1115)
触摸按键（计数）
- 基于51单片机的电容触摸按键功能，通过简单的读取IO口电平实现(Based on 51 single chip microcomputer, capacitor touch button function is realized by simply reading IO port level)
keil下STM32F1使用IO模拟串口
- keil平台下STM32F1使用IO模拟串口(Stm32f1 uses IO analog serial port on keil platform)
2个IO实现8*8 LED点阵电路
- 2个IO控制2片74HC595电路实现一个8*8 LED点阵电路