搜索资源列表
MQ-2
- MQ2烟雾传感器制作过程，能够显示实时空气中的烟雾含量-MQ2 smoke sensor production process, it is possible to display the real-time air in the smoke content
SMOKE_test
- CC2540烟雾报警器模块测试程序 烟雾报警器，检测到烟雾时，GPIO输出高电平，报警消失后，变低电平-CC2540 module test procedures smoke alarm smoke alarm, when smoke is detected, GPIO output high, the alarm disappears, goes low
JCSD
- 基于nRF4010的烟雾检测系统，具有自动控制功能，此部分为检测发送部分程序，已用过，具有一定参考价值-Based on nRF4010 smoke detection system with automatic control functions, sending part of this part of the test procedures have been used, with some reference value
M32
- 用于实时监控一定范围内的烟雾变化，并把状态通过无极性二总线传输给主机。-For real-time monitoring of a range of smoke changes, and the state of polarity of the second bus through transmission to the host.
ds18b20PhongwaiPyanwuPchaoshengbo
- 此程序为毕业设计之防火防盗报警器具有MQ2烟雾报警，DS18B20温度报警，红外传感器感应人体红外，超声波感应人得进入，加上1602液晶显示等功能，同时具有蜂鸣器及LED报警-This procedure for the graduation of the fire alarm system design has MQ2 smoke alarm, DS18B20 temperature alarm, human infrared sensor infrared sensor, ultrasoni
MQ-2
- MQ-2烟雾传感器的程序，单片机是MS9S12D64-MQ-2 smoke sensors, SCM is MS9S12D64
ANFANGCHENGXU
- 安防报警程序。红外报警和烟雾报警。可以通过GSM发短信，AT24C02存储电话号码，可更改。-Security alarm program. Infrared alarm and smoke alarm. Can send messages through the GSM, AT24C02 to store phone number, can be changed.
yanwubaoji
- 利用Keil Uvision4阮籍，基于51单片机的烟雾报警程序-Use Keil Uvision4 Ruan, 51 MCU-based smoke alarm program
wuxianduodian
- 无线监测温湿度和光监测，以及烟雾浓度，把数据传回终端显示报警，可以上下调温湿度。-Wireless monitoring temperature, humidity and light monitoring, and smoke concentration, the data returned by the terminal display alarms, up and down the thermostat and humidity.
SY_B116A
- 单片机控制油烟机电机的档位 以及油烟机按键显示，按键是用触摸控制的-MCU control smoke machine motor stalls and hood buttons display, keypad with touch control
CC2530smoke-alarm
- CC2530 烟雾报警器。一个简单的例程-CC2530 smoke alarm.
temp_remindianzu
- 实现了温度采集和串口数据上传，波特率19200，温度传感器采用热敏电阻，并可外挂开关量类型的传感器如烟雾、温度、火焰等等，实现自己的协议转换-Achieve a temperature acquisition and serial data upload, baud rate 19200, thermistor temperature sensor, and plug-in switch types of sensors such as smoke, temperature, flame, et
MQ-2
- 利用MQ-2烟雾传感器和单片AT89S52，测量烟雾，预防火灾-Using the MQ-2 smoke sensors and monolithic AT89S52, measuring smoke, fire prevention
zhong
- 数字钟，实现整点报时以及校时功能，烟大数字逻辑课程实验。-Digital clock, realize the whole point timekeeping and school function, smoke large digital logic course experiment.
intelligent-wireless-alarm-system
- 本文介绍了一种操作方便!运行可靠的智能型无线报警系统"它集防盗贼入侵!防火灾!防 有害气体泄露等功能于一体,可实现自动检测和电话自动报警"自动检测是指由各种复合式探测 器或传感器实现对住宅的各种模拟信号(人体发出的红外信号!温度!烟雾浓度!有害气体浓度 等)进行自动监测,复合式传感器的应用使得系统可靠性增强"自动电话报警是指系统通过电话 线路自动拨打户主或相关部门的电话,发出语音求救信号"智能探测器在监测到灾情时只输出报 警信
yanwubaojing
- 利用红外传感器检测烟雾，如果浓度过高就开始报警，起到防火的作用-Infrared sensor detects smoke, the alarm if the concentration is too high to start, play a role in fire
HT45F23A---SmokeSensor----Voice
- 附件利用holtek MCU HT45F23A开发语音型烟雾侦测器的原始代码，可完成烟雾火灾的报警和语音播放。附件包含对应电路图，提供给大家参考-Accessory use holtek MCU HT45F23A development of voice-type smoke detectors in the source code, to be completed by the smoke of fire alarm and voice playback. Annex contains the
JCSD
- 基于nRF4010的烟雾检测系统，具有自动控制功能，此部分为检测发送部分程序，已用过，具有一定参考价值-Based on nRF4010 smoke detection system with automatic control functions, sending part of this part of the test procedures have been used, with some reference value
BS84B08A
- 采用BS84B08A开发的油烟机，带自动升降功能。-BS84B08A developed using smoke machines, with automatic lifting function.
PIC16F676_AD
- PIC16F676 用于感烟探测器中的AD采样程序。两次采样，后次减前次即为采样值-PIC16F676 for smoke detectors in the AD sampling procedures. Two samples, after the meeting by the previous sampling value is