搜索资源列表
步进电机控制实验程序清单
- 步进电机控制实验程序清单(mcs51系列,doc格式)-experimental procedure list (mcs51 series, doc format)
通用伺服电机控制
- 通用伺服电机控制原理及C源码, 内含: 关于步进伺服电机加速曲线计算器的使用说明,举例说明参数使用方法的步进电机控制的具体编程。供参考,PDF文档。 步进、伺服电机加速曲线计算器修正版。-generic servo motor control principle and C source, consisting of : Stepping on the servo motor speed up the curve for use of the calculator, example
步进电机控制试验
- 步进电机控制试验-stepping electromotor controll experimentation
单片机 步进电机控制原代码
- 单片机 步进电机控制原代码-stepper motor control microcontroller source code
可控3相步进电机控制(单片机汇编)
- 可控3相步进电机控制(单片机汇编)可控制步进电机精确转动,调速,正反转。
4线步进电机控制
- 4线步进电机控制
完整的控制程序和非常详细步进电机控制原理图
- 完整的控制程序和非常详细步进电机控制原理图,安装PROTEUS后就可以看到仿真的结果,Complete control procedures and a very detailed schematic stepper motor control, the installation can be seen after the PROTEUS simulation results
基于矢量控制的永磁同步交流伺服电机控制系统
- 基于矢量控制的永磁同步交流伺服电机控制系统 可以用的源程序,Based on vector control of permanent magnet synchronous AC servo motor control system can use the source code
串口+按键控制步进电机
- 步进电机控制的C程序,是自己不太会写,所以参照其他网站下载的程序,大家可以看一下(Stepper motor control C procedures, is that they do not write, so refer to other web site download procedures, we can look a)
步进电机控制
- 本篇说明文档介绍了基于RX/23T单片机的步进电机控制。主要介绍了如何在代码生成工具e2 studio下配置本例程所需要的CLOCK、PORT和MTU等模块并生成相应的驱动代码,同时对生成代码文件添加的步进电机控制、转速调整等功能进行了详细说明。最后附步进电机控制实例。(This document describes the stepper motor control based on RX/23T microcontroller. Mainly introduces how the code
Renesas 直流无刷电机控制应用示例 源代码
- Renesas 直流无刷电机控制应用示例 源代码(Renesas Brushless DC motor control application example source code)
分享TMS320F28335的永磁电机控制编程实例
- 利用F28335实现永磁电机的控制实例,从而实现基于ccs的电机控制编程(The control example of permanent magnet motor is realized by using F28335, and the motor control programming based on CCS is realized)
可以运行在dsPIC30F微处理器上的电机控制代码
- 可以运行在dsPIC30F微处理器上的电机控制代码(The motor control code that can run on the dsPIC30F microprocessor)
DSP2812三相异步电机控制
- 通过DSP2812实现对三相异步电机速度的控制(Speed control of three phase asynchronous motor through DSP2812)
Altera官方FPGA电机控制的中文文档
- Altera官方FPGA电机控制的中文文档,很不错的参考资料(Altera Official FPGA Motor Control Chinese Document, Good Reference)
2019.4.26修改2电机控制
- 通过stm32来控制2个步进电机,可以拿来修改2轴控制(Two stepper motors are controlled by stm32, which can be used to modify two-axis control.)
用DSP2812开发的无刷直流电机控制程序
- 用DSP 2812进行无刷电机控制开发的相关程序。(The relevant program of brushless motor control development with DSP 2812.)
至尊型DSP28335-10KW电机控制开发学习套件资料
- 至尊型DSP28335-10KW电机控制开发学习套件资料(Supreme dsp28335-10kw motor control development learning kit materials)
电机控制原理图
- 基于STM32F407ZGT6,PWM电机驱动及控制,集成MPU6050,预留蓝牙接口(Based on stm32f407zgt6, PWM motor drive and control, integrated mpu6050, reserved Bluetooth interface)
STM103步进电机控制
- STM103VCT6实现多轴步进电机控制(Stm103vct6 realizes multi axis stepping motor control)