搜索资源列表
DE2_i2sound
- DE2_i2sound.rar，大家快来下啊，做好了的IP核-DE2_i2sound.rar, everyone is breaking under ah, do a good job of the IP Core
DE2_Top
- DE2_Top.rar，做好了的IP核，大家开来下啊！-DE2_Top.rar, do a good job of the IP core, open to everyone under ah!
testuclinux
- 用来在fpga下移植uclinux的测试程序 希望对大家有帮助-Used in the FPGA under test procedures transplantation uClinux hope everyone has to help
4NET_and_4NET.V_R1.2.51_0I0H18_Aug.27-2009
- GM8120/FA526 Firmware (binary) Panda 4NET VGA (Hunt HDR-04DE)
bootram
- chuong trinh giao tiep voi SDRAM
share_spi_ok
- CHUONG TRINH GIAO TIEP VOI SPI
system_control
- dieu khien chung cho he thong so
uart_ok
- dieu khien giao tiep uart
ram_harvard2
- dieu khien giao tiep voi RAM
uart_rtl
- uart模块的rtl代码，verilog编写。-uart module rtl code, verilog prepared.
fpga
- 嵌入式fpga示波器采集配置及源码 采用keil4，兴建工程-The embedded FPGA oscilloscope acquisition configuration and source
linux-nios
- 嵌入fpga内的niosii，uClinux的sopc软件，很有用-sopc uClinux
Verilog-VGA
- 这是我用Verilog 在ISE软件编写设计的一个基本的VGA显示程序，需要使用Spartan 3E来实现VGA程序在显示器上显示，显示图形，静态图形600*800分辨率，将屏幕四等分，并分别显示不同的颜色，建议初学者参考-This is a basic VGA I used to write Verilog design in ISE software display program, you need to use Spartan 3E to implement the program on
cf_lib
- 基于zedboard-7000的HDMI FPGA IP控制核-HDMI FPGA IP control core based on Zedboard-7000
IR_4CE30_USB2.0
- 红外接收将EP4CE30 VER2.0插在USB2.0 VGA SD Expansion Board板上下载程序。红外发射器上按键0-9，对应在EP4CE30 VER2.0对应LED4-LED1显示“0000”-“1001”。其他按键显示“1111”-EP4CE30 VER2.0 infrared receiver will download USB2.0 VGA SD inserted in the Expansion Board board. Infrared transmitter but
4CE6_ADC
- 关于AD转换的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for AD conversion，debugging on EL-ARM-DSP-IV experiment box.
4CE6_DAC
- 关于DA转换的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for DA conversion，debugging on EL-ARM-DSP-IV experiment box.
4CE6_DCMOTOR
- 关于直流电机的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for DC motor，debugging on EL-ARM-DSP-IV experiment box.
4CE6_UCOS
- 关于UCOS的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for UCOS，debugging on EL-ARM-DSP-IV experiment box.
4CE6_STEPMOTOR
- 关于步进电机的NIOS源码程序，已调试，建议在EL-ARM-DSP-IV实验箱上调试。-NIOS source program for step motor，debugging on EL-ARM-DSP-IV experiment box.