搜索资源列表
Debugger8051(v1.9)8051xiliedanpianjifangzhenruanji
- 8051系列单片机仿真软件 Windows9x 汉化版）编辑、模拟、调试、仿真器， 全中文Windows界面，可以直接编写汇编语言程序， 生成写目标文件，支持单步、断点等调试、仿真方式， 根本不用学就会使用的软件。 该软件小巧好用，功能齐全、免安装，解压缩后即可使用。-8051 microcontroller simulation software Windows9x Chinese Version) editing, simulation, debugging, Simul
X5045-1
- x5045有四种功能：分别是上电复位、看门狗定时器、电源电压监控和块锁保护串行eeprom的功能， 该程序通过改变控制寄存器的参数可以实现看门狗定时器监视电压和设置保护rom区，每次复位后 地址计数器都是该区的首地址（个人观点），即断点地址。 问题：其实对该芯片的应用还是很模糊-x5045 four functions : the reduction of electricity, watchdog timer, Supply voltage control and protecti
U-EC5.rar
- 。该工具可实现单步、连续单步、断点、停止/运行,支持寄存器/存储器的观察和修改,下载程序到Flash存储器等功能。另一特点为可使用专用软件（U-EC5中文编程软件）快速将程序代码烧录到C8051F MCU中,. The tool enables single-step, continuous single-step, breakpoint, and stop/run in support of register/memory of observation and modify, download
keilc51introductions
- Keil工程文件的建立、设置与目标文件的获得 Keil的调试命令、在线汇编与断点设置 Keil程序调试窗口 Keil的辅助工具和部分高级技巧-Keil project document to establish, set up with the target document was Keil debugging command-line compilation and debugging breakpoint set Keil window Keil tool and a numb
uvision
- Vision2 调试命令详解，包括存储器命令、程序命令、断点命令、通用命令等。-Vision2 debug commands Xiang Jie, including memory command, the program command, a breakpoint command, general orders.
interrupt67
- 此程序测试C8051F020的中断6、7，可在相应的两个中断中设断点观察，中断处理时发光二极管的状态也相应的会有改变.-C8051F020 interrupt this program testing 6,7, can set the appropriate breakpoint observed in the two interrupt, interrupt processing status LED' s will change accordingly.
c8051cp1
- c8051,此程序可完成CP0比较器的比较功能，比较器CP0+来自于VREF引脚,CP0-由S2控制.按下S3后,比较器响应后将产生中断,可在中断程序中设断点观察. -c8051, this program can complete the comparison function CP0 comparator, the comparator CP0+ from VREF pin, CP0-controlled by the S2. Press the S3, the comparator w
COUNT
- 利用8088/86外接8253可编程定时器/计数器，可以实现对外部事件进行计数。设置断点读回计数器的值。-8253 by 8088/86 external programmable timer/counter can count external events. Breakpoint counter value read back.
EEPROM24C02
- 该程序演示如何使用EEPROM芯片对数据进行读写，以实现数据的掉电保存。下载实验程序后，按动按键S17、S18对数值进行修改，断点后再上电，发现掉电前的数值依然显示在LED上-The program demonstrates how to use read and write data EEPROM chip to save power-down data. Download the test program, press the button S17, S18 modification to
149_ta_22
- ACLK / 8 P1.1的输入捕捉（TA0）_NOP（）指令运行到断点看到16捕捉值的差异。 ACLK = 32768Hz的，MCLK = SMCLK =默认〜 800kHz的外部时钟晶振上辛XOUT需要为ACLK -ACLK/8 P1.1 input capture (TA0) _NOP () command to run to the breakpoint to see 16 to capture the value of the difference. ACLK = 32
Source1
- 实现单片机外部存储器的找断点程序，可以节省外部存储器的内存空间-MCU external program memory breakpoint to find
Electronic-clock
- 利用单片机编写的电子钟表，有4个定时闹钟，可以断点保护，需要24C02的驱动程序。-Written by SCM electronic clocks and watches, has four timing alarm clock, can breakpoint protection, need to 24 C02 of the driver.
EXP24-CP1
- 此程序可完成CP1比较器的比较功能，比较器基准信号来自于VREF引脚, 比较器响应后将产生中断,可在中断程序中设断点观察. -This program can be completed CP1 comparator compare function, the comparator reference signal from the VREF pin, comparator response will generate an interrupt, set the breakpoint
dac
- 控制DAC输出模拟电压.控制程序运行到应设置断点处，观察LED亮度或者测量 DAC的输出电压数值-Control DAC output analog voltage control procedures should be set to run to the breakpoint, observe the LED brightness or measuring the DAC output voltage value
DS18B20-EEPROM
- DS18B20的EEPROM的程序 51单片机 可以断点保存报警温度。很难得。一般找不到的-DS18B20 program 51 microcontroller' s EEPROM can save breakpoint alarm temperature. Difficult to get. Generally can not be found. . .
WDT_demo_V101
- 该程序描述看门狗定时器的使用方法和寄存器配置问题，注意debug调试对看门狗不能做断点调试-The program describes the methods and the use of the watchdog timer register configuration issues, note the debug breakpoint debugging on the watchdog can not do
I2C24C02
- I2C通信，用24C02进行存储，断电保存，上电恢复，继续断点处运行。-I2C communication with 24C02 storage, power saving, power-recovery operation to continue breakpoint
U-EC5program
- 可实现单步、连续单步、断点、停止/运行,支持寄存器/存储器的观察和修改,下载程序到Flash存储器-Can achieve single-step, continuous single step, breakpoint, stop/run, supports inspection and modification register/memory download to Flash memory