搜索资源列表
ADsample
- 通过AD校正来提高2812 AD采样的精度，AD采样频率为10K，序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器，采样模式采用顺序采样。利用通用定时器T1的周期中断事件来启动AD转换。-By AD 2812 AD correction to improve the accuracy of sampling, AD sampling frequency of 10K, the sequence generator SEQ1 and SEQ2 cascaded into a 16-cha
Adc_T1_start
- AD采样频率为10K，序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器， 采样模式采用顺序采样。利用通用定时器T1的周期中断来触发AD转换。-AD sampling frequency of 10K, the sequence generator SEQ1 and SEQ2 cascaded into a 16-channel sequencer, sampling mode with sequential sampling. The use of general-purpose ti
Adc_T1_correct
- AD采样频率为10K，序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器， * 采样模式采用顺序采样。利用通用定时器T1的周期中断来触发AD转换。 ADCINA0和ADCINB0为参考电平，对ADCINA0,ADCINA1，ADCINB0，ADCINB1连续10次采样，然后分别排序，滤波，取均值，用A0，B0的值计算增益和偏移量，用来校正A1，B1-AD sampling frequency of 10K, the sequence generator SEQ1 and SE
DC-power-module-design
- 该文件讲述TMS320C6000系列的电源供电模块芯片的上电循序、过载保护、电路板布线注意事项，讲述如何设计一个C6713适用、好用的电源模块。-The document describes TMS320C6000 series of power supply module power-on-chip sequential, overload protection, circuit board layout considerations, how to design a C6713 applic
F2812_AD01
- F2812 ADC01 （CCS3.3开发环境下）软件置位启动AD转换，实现ADC模块16路通道的采样。序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器，采样模式采用顺序采样。-F2812 ADC01 software is set to start AD conversion, the ADC module 16-channel sampling. Sequencer SEQ1 and SEQ2 cascade into a 16-channel sequencer, samplin
ad
- AD采样程序，由CPUTimer2中断产生PWM，再用ADC的A0和A1进行顺序采样。-AD sampling program, by CPUTimer2 interrupt produces PWM, then use the ADC A0 and A1 sequential sampling.
2812ADsample
- AD采样频率为10K，序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器，采样模式采用顺序采样。利用通用定时器T1的周期中断事件来启动AD转换。ADCINA0和ADCINB0为参考电平，实际的电压值分别为0.420和1.653,由于每个板子的具体特性稍有不同，请用万用表自行测量参考电压值。此例程对ADCINA0、ADCINA1、ADCINB0、ADCINB1四个通道进行连续10次的采样，然后对各个通道的10个采样值进行排序，滤波，最后取平均值。然后由ADCINA0和ADCINB0通道的值
adc_seq_ovd_test
- 利用28335来进行AD采样，使用8个采样通道，进行双序列顺序采样。-Use of 28 335 to AD sampling, using eight sampling channels, double sequence sequential sampling.
09_ADC01
- 说 明：序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器，采样模式采用顺序采 样。AD采样的触发方式采用软件置位的方式 -Descr iption: SEQ2 sequencer SEQ1 and cascaded into a 16-channel sequencer, sampling mode using sequential sampling. AD sampling using software trigger mode is set way
AD01
- 软件置位启动AD转换，实现ADC模块16路通道的采样。采样模式采用顺序采样。AD采样的触发方式采用软件置位的方式-Software setting start the AD conversion, the realization of channel sampling ADC module 16 road.In a sequential sampling mode.AD sampling way of trigger with the method of setting software
ADC1_2classic
- DSP2812经典AD采样程序，ADC顺序级联方式，中断读数-DSP2812 classic AD sampling program, ADC sequential cascade, interrupt reading