搜索资源列表
296_demo_ic
- 80296SA的应用开发，包括各种io操作。附带芯片的英文手册。-80296SA application development, including io operations. English manual that came with chips.
55555
- sim32单片机的io口编程学习例程编译调试通过，是单片机的合理利用例程-sim32 microcontroller io port programming learning routines compiled debugging through the rational use of the microcontroller routines
STC15V3.0
- STC 15/12系列例程，资源丰富，包括定时器、spi、iic、io口控制-STC 15/12spi、iic、io
servo
- STM32驱动舵机程序，如果舵机不动需要在IO口和信号线之间串联一个10K电阻-STM32 driver steering program, if the steering gear real need between IO port and the signal line is connected in series with a 10K resistor
PWM
- 51单片机的单个io口pwm通过定时器的调试程序-A single IO port PWM 51 singlechip timer program debugging through
STM32-I2C
- STM32硬件读写I2C,比用IO读写方便多了-STM32 wirte or read I2C
Interfacing-with-a-Philips-PCF8574-8-bit-IO
- The PCF8574 uses the Philips I2C 2-wire protocol and provides eight I/O channels per device. Eight such devices may be cascaded by setting the A2, A1 and A0 leads to uniquely identify each device. In addition, up to eight PCF8574A devices may
ADuC7026-KEYS
- ADuC7026 的按键显示程序，主要对7026的io口的操作-ADuC7026 button display program, mainly for 7026 of io port operations
BrdVerify
- Arduino库。用于arduino单板的IO口开路、短路测试；串口速率测试；流水灯测试。 -Arduino library. Arduino board for IO port open, short test serial rate test water lights tested.
sio_wdt
- 此程序展示在QNX环境下如何操作SuperIO的看门狗。此示例很好地显示了如果在QNX系统下获取IO端口操作权限，并启用看门狗功能-This program shows how to operate under the QNX environment SuperIO watchdog. This example if you get a good indication of the IO port authority to operate under the QNX system, and en
GPIO_LED
- 关于stm32f107的IO程序，已在ALIENTEK MiniSTM32开发板上验证。
test1_zigbee
- 物联网开发之zigbee基础实验，实现控制io状态-zigbee io state
Stm32-IOOV7670-V1.0(keil)
- stm32 io 口直接驱动ov7670 直接采集图片-stm32 io port directly drive ov7670 direct acquisition Photos
IOdemo-code
- 基于盛博综合I/O嵌入式板卡的AD\IO MFC编程。已经包含了所需的Dll和Lib 文件！-Sainsbury based integrated I/O embedded board AD \ IO MFC programming. Already contains the required and Lib Dll files!
io
- 过单片机的I/O口控制LED的亮灭，从而观察I/O口的输出。实验2通过单片机的I/O口接受按键动作信息，然后通过LED和数码管指示-Through the microcontroller I/O port control LED light off, thereby observing the output I/O port. Experiment 2 through the microcontroller I/O port to accept keystrokes information an
CC2430
- CC2430无线模块的学习套件的范例代码，包含AD通道单次循环，IO口全测试，串口通信，点对点无线通讯等源代码，很适合初学ZigBee无线网络的同学。-Learning Suite sample code CC2430 wireless module, including AD channel single cycle, IO mouth full test, serial communications, point to point wireless communications source
107canio
- stm32107can，收发，可以查询io口的状态，波特率为500k。-stm32107can, transceiver, you can check the status of io port, baud rate is 500k.
MSP430x2xx-chinese-learning
- MSP430x2xx系列中文版学习资料，定时器、SPI、IO、中断、iic、ADC、clock等模块学习-MSP430x2xx service information
DHT11
- 因要熟悉CSR1010的基本IO操作，未用蓝牙功能，就用它来做主控MCU驱动温湿度传感器DHT11，并送入两片595增大负载能力的数码管中显示做人机交互。-Because of konwing basic IO operation of CSR1010,without using bluetooth function ,only viewing it as general MCU to drive temperature and humidity sensor DHT11 and sending
softUartRxd
- 单片机软件模 串口接收 用普通io口-uart rxd