搜索资源列表
ZnO
- ZnO压敏电阻伏安特性编程-ZnO
simulink
- 电阻式处理炉温控系统设计,simulink仿真单回路系统以及串级系统和simith预估控制系统设计。-Resistive treatment furnace temperature control system design, simulink simulation of single-loop system, and a cascade system and simith predictive control system design.
RC
- RC常用标值电阻电容,常用标值电阻电容.-RC
qodncskfh
- 低通滤波器让某一频率以下的信号分量通过,而对该频率以上的信号分量大大抑制的电容、电感与电阻等器件的组合装置。 -low-pass filter
ttt
- 让某一频率以下的信号分量通过,而对该频率以上的信号分量大大抑制的电容、电感与电阻等器件的组合装置。 -low-pass filter
ff
- low-pass filter 让某一频率以下的信号分量通过,而对该频率以上的信号分量大大抑制的电容、电感与电阻等器件的组合装置。 -low-pass filter
gh
- 让某一频率以下的信号分量通过,而对该频率以上的信号分量大大抑制的电容、电感与电阻等器件的组合装置。 -low-pass filter
resistor-rate
- 从百分之1 或5 精度电阻中选择满足串联比值和误差值电阻的电子表格工具,适合于硬件设计人员使用,希望喜欢。-From 1 or 5 resistor selected to meet the series resistance error ratio and spreadsheet tools for hardware designers to use, hope you like it.
11
- 该电路由一片四双向模拟开关集成电路CD4066为核心构成。每个电路内部有四个独立的能控制数字或模拟信号传送的开关。当水箱无水时,由于180K电阻的作用,使四个开关的控制端为低电平,开关断开,LED 不发光。随着水位的增加, 由于水的导电特性,使得IC的13脚为高电平,S1接通,LED1点亮。当水位逐渐增加时,LED依次发光指示水位。水满时, LED4发光, 显示水满。同时T1导通, B发出报警声,提示水已满。不需要报警声时,断开开关K即可。 -The circuit consists of a
05138775
- 直接转矩的智能控制,包括模糊电阻辨识,模糊开关表的内容-Direct torque intelligent control, including fuzzy resistance identification, fuzzy switch table content
es
- 恒流源的陀螺仪测温丝电阻测量电路的设计-Gyro temperature constant current source circuit wire resistance measurement
v0.2
- 基于matlab gui的电路仿真系统,包括电阻电路仿真、动态电路仿真和时域仿真-Matlab gui-based circuit emulation systems, including the resistance of circuit simulation, dynamic circuit simulation and time domain simulation
ekfpmsm-r
- 基于卡尔曼滤波器的永磁同步电机的二阶电阻辨识-Kalman filter based on permanent magnet synchronous motor of the second-order Resistance Identification
zhuansuguji
- 基于卡尔曼滤波器的PMSM的电阻估计模型-Kalman filter based estimation model for the resistance of PMSM
kirch
- kirch 网络等效电阻问题 给定一个由n 个结点构成的网络电路,结点编号为1,2,…,n。结点间连接着m个电 阻。网络等效电阻问题要求计算结点1和n 之间的等效电阻。-kirch equivalent resistance network of a given problem of n nodes of a network circuit, nodes numbered 1,2, ..., n. Connected between nodes m-resistance. Problem r
kni
- kni 骑士共存问题 给定一个由n 个结点构成的网络电路,结点编号为1,2,…,n。结点间连接着m个电 阻。网络等效电阻问题要求计算结点1和n 之间的等效电阻-kni Knight coexistence given an n-node network consisting of circuit nodes numbered 1,2, ..., n. Connected between nodes m-resistance. Equivalent resistance network pro
Antenna-load
- 集总元件电阻、电感、电容的模拟,用不同大小的电感和电容加载,看天线的辐射方向图,从而分析加载天线的特性-Lumped resistance, inductance, capacitance of the simulation, using different sizes of inductors and capacitors to load to see if the antenna radiation pattern, to analyze the characteristics of the
RLC
- RLC串联电路暂态过程临界阻尼电阻的傅里叶分析.-Series RLC circuit transient Fourier analysis of the critical damping resistance.
Ladder_Register_Clac_by_Struct
- 作业:利用结构实现阶梯型电阻电路计算 C++上机作业,需要的话可以参考-Homework:Ladder-Resister-clac by struct on C++
Ladder_Register_Clac_by_Class
- 作业:C++作业,利用类实现阶梯型电阻的计算。上机的作业,供参考-Ladder Register Clac by Class