搜索资源列表
TestServer
- 一个用来统计误码率并利用socket对象实时发送的小的界面程序,可以配置误码统计的参数。-used a statistical error rate target socket and use real-time transmission of the small interface procedures, statistical error can be configured parameters.
rscode-1.0
- 无线通讯中使用的一种揪错算法,rs 1.0 揪错能力可配置 能纠正 (冗余长度)/2-1 个错误 -wireless communications used in a clutch wrong algorithm, rs 1.0 ferret capacity can be configured wrong to be corrected (Redundant length) / 2-1 mistake
AprioriAlgorithm
- 在使用时,请先在“控制面板/管理工具/数据源ODBC”中配置数据源,名称为“TRANSACTION”,数据库在 Apriori 文件夹下。-when used, the post "Control Panel / management tools / ODBC data source," the source of configuration data, known as "TRANSACTION", the database Apriori folder
2Tx2RxSpatialMultiplex
- 该文件夹为空间复用空时码的仿真程序,天线配置为2发2收。 主要程序的用途说明: mainMIMO_OFDMA_2Tx.m: 主程序,设置各种参数 gendata_2Tx_SM.m: 生成原始信息数据的程序 mod_2Tx_SM_DFUSC.m:调制程序 gen_SUI_CorrCIR.m: 生成信道冲击响应的程序 get_perfectCE_2x2.m: 生成理想信道估计值的程序 chanSUI_corr_2x2.m: 发送信号通过SUI信道的程序 a
2Tx_2Rx_STBC
- 该文件夹为Alamouti空时码的仿真程序,天线配置为2发2收。 主要程序的用途说明: mainMIMO_OFDMA_2Tx_SER.m: 主程序,设置各种参数 gendata.m: 生成原始信息数据的程序 mod_2Tx_STBC_DFUSC.m:调制程序 gen_SUI_CorrCIR.m: 生成信道冲击响应的程序 get_perfectCE_2x2.m: 生成理想信道估计值的程序 chanSUI_corr_2x2.m: 发送信号通过SUI信道的程序 addA
2Tx_2Rx_STBC_MAP
- 该文件夹为空时块码-卷积码级联系统的仿真程序,天线配置为2发2收。 主要程序的用途说明: mainMIMO_OFDMA_2Tx_Convcode.m: 主程序,设置各种参数 gendatabits.m: 生成原始信息比特数据的程序 conv_encoder.m: 卷积码编码器 interleave.m: 交织器 mod_2Tx_STBC_DFUSC_Convcode.m:调制程序 gen_SUI_CorrCIR.m: 生成信道冲击响应的程序 get_perfect
4Tx_2Rx_STBC
- 该文件夹为Alamouti空时码的仿真程序,天线配置为4发2收,与大家共享。-folder for the ACS code of space-time simulation program, antenna configuration for four 2 admission. and share.
a-JJ-algeorith-for-state-eqation
- 在MATLAB环境下,对六变量的状态方程进行极点配置仿真源代码。-in MATLAB environment, the pair of six variables for the equation of state pole configuration simulation source code.
comdraw
- 串口发送接收数据。可配置端口,波特率等。 发送可选择ASCII方式或HEX方式。 中断方式接收数据。 可以通过ADC和MCU可以把数据通过 串口直接发送到PC上让MATLAB分析-receiving data. Configurable ports, baud rate, and so on. Send option HEX or ASCII mode. Interrupt receiving data. Through the MCU and ADC data can b
fft
- 可以配置点数的fft算法源代码,注释很详细
F330_CC1100
- C8051F330与CC1100的基本配置。
decoupling_pole
- 解耦控制要求下的极点配置MATLAB算法。 关键词:解耦控制 极点配置 线性系统 MATLAB-A matlab algorithm of arbitrary pole- assignment in the sense of decoupli countrol
adptive
- 利用自适应控制算法,进行参数自整定和进行极点配置-adptive control for setting poles
PSO
- 建立柔性板和压电作动器耦合模型,运用粒子群算法进行配置优化(The coupling model of flexible plate and piezoelectric actuator is established, and the particle swarm optimization algorithm is used to optimize the configuration)
程序作业三:极点配置
- 多极点配置程序,循环矩阵的判断与化简,并在多极点配置中还使用了单极点配置(The multi pole configuration program, the judgement and simplification of the cyclic matrix, and the use of single pole configuration in the multi pole configuration)
新建文件夹
- 构建状态观测器的例子 极点配置 希望对大家有些许帮助(An example of building a state observer)
yichuansuanfa
- 使用遗传算法优化风、光、燃气互补发电最佳配置(Genetic algorithm is used to optimize the optimal configuration of wind, light and gas complementary power generation)
123
- 通过风电场的实际功率和预测功率进行风储功率容量配置(Wind Storage Power Capacity Configuration)
Untitled6
- 利用粒子群算法对储能的容量配置进行最优寻优(Energy storage capacity optimization)
智能微电网中利用粒子群算法实现微电网多目标优化
- 针对智能微电网优化配置问题,分别对微电网中风机、光伏和储能电池进行容量设计,并采用粒子群算法对系统进行优化配置。(Aiming at the optimization configuration of the smart microgrid, the capacity design of the wind turbine, photovoltaic and energy storage batteries in the microgrid are respectively carried out