搜索资源列表
液晶lcm19264 驱动
- 20051104调试通过 液晶驱动 采用24m晶振-20051104 through the LCD driver debugging using crystal 24m
FDTD模拟光子晶体光纤中光的传播
- %This program calculate the wave guide by a photonic crystal. %For two dimension case. %Only for TM case, in this version.
persional-PC
- 学习光盘（HC6800）单片机源码包括液晶显示、按键控制、AD转换、串口通信等。-Learning CD-ROM (HC6800) microcontroller source including liquid crystal display, button controls, AD converter, serial communications.
crystalexcel
- 这是一个水晶报表开发的一个程序，对初学者来说也是很有帮助的。-This is a Crystal Reports development of a procedure is also helpful for the beginners.
chuanshong
- 向串口发送数据。 说明：使用外部11.0592MHz晶振，系统时钟配置后Fpclk=11.0592MHz； 通讯波特率115200，8位数据位，1位停止位，无奇偶校验。-Send data to the serial port. Descr iption: the use of an external 11.0592MHz crystal oscillator, system clock configured Fpclk = 11.0592MHz communication bau
1602
- 此程序为1602的开发程序 使用的为c语言来进行编程-1602 liquid crystal display procedures www.pudn.com name is lizzy115
shuij
- crystalreportviewer控件允许在应用程序中查看 Crystal Report。ReportSource 属性用于设置要查看哪个报表-crystalreportviewer controls allow applications to view Crystal Report. Attribute to set ReportSource To see which statements
shuippt
- 以前在VB6水晶报表里设置了个参数@aa，在代码处写 Cry1.Formulas(1) = "aa= 123 ",则可在报表处显示出来。” 你这样应该是公式-Crystal Reports in VB6 ago set up parameters in @ aa, the Department write code Cry1.Formulas (1) = " aa =' 123 ' " , can be displayed in the statements o
LCD
- 了解点阵液晶显示实验的工作原理掌握点阵液晶显示实验程序的设计方法.本实验板中使用的是内置12864A 的液晶屏12864A 由两片带控制器的列驱动电路 KS0108 和一片行驱动电路KS0107 组成主要的硬件电路另外还可以附加负压发生电路 显示方面由一片128*64 点的液晶片组成-Dot-matrix liquid crystal display experiments to understand the working principle of the experiment hav
MSP430_GUI
- 430液晶驱动，可以兼容大量液晶，附有各类头文件-LCD driver 430, a large number of liquid crystal can be compatible with various types of header files
LCD12864
- LCD12864系列图形点阵液晶显示模块使用说明书,学习液晶12864必备！-LCD12864 series of graphics to use dot-matrix liquid crystal display module manuals, learning the necessary LCD 12864!
MCU_Init
- Freescale MCU 带CAN通讯 MC9S08DZ16 初始化，包刮各端口及总线频率调置。用8MHz晶体谐振器获得16MHz总线频率。-Freescale MCU with CAN communication MC9S08DZ16 initialization, including scraping the port and bus frequency modulation home. 8MHz crystal resonator used to obtain the frequency
12864yejing
- 基于IAR开发环境的液晶12864的完整的开发资料及手册-IAR development environment based on liquid crystal 12864 for complete development of information and manuals
crystaldisplay
- 通过拔码开关控制FPGA在液晶显示器上实现汉字的显示，其中涉及到一些时序控制-FPGA switch control code by removing the liquid crystal display to achieve the display of Chinese characters, which involves a number of sequential control
LEDDAZHUANPAN
- CHIP SN8P2604 ------------------------------------------------------------ 功能描叙：开机为全灭 I)KEY按下。A区工作：A区灯加速后减速最后停止，再在原地闪 0.3SH+0.3SL，B区为不亮 II)KEY按下。B区工作：B区灯加速后减速最后停止，如果B区最后停点与A区同，A区与B区同时亮灭 （A区B区灯的颜色和停止点都为随机产生） 如果A区与B区最后停点不同，A区与B区互亮互灭
gpsPproteusP52
- 本系统采用51单片机为处理器以带字库的12864或1602液晶显示作为人机对话接口，硬件部分主要采用GPS模块、STC89c52RC单片机、1602液晶显示器或带字库的12864液晶显示器等组成，GPS模块发送的串行数据送至单片机串行口，经单片机处理后送到液晶显示器进行显示。-The system uses the font of 51 single-chip processor to 12864 or 1602 LCD as the man-machine dialogue interface
xunjixiaoche
- 利用循迹信号采集模块中的红外发射接收对管检测路面上的轨迹 将轨迹信息送到fpga，fpga将轨迹信息通过led灯显示出来，在通过fpga发轨迹信号给单片机，通过单片机来控制电机的转动。同时单片机将小车的状态反馈给fpga，fpga通过1602液晶显示小车的状态。-Infrared tracking signal acquisition module transmitting and receiving tube detection on the road trajectory to the
ech33
- fdtd 1d photonic crystal Band diagram
msp430x20xx_dco_flashcal
- // Descr iption: This code re-programs the F2xx DCO calibration constants. // A software FLL mechanism is used to set the DCO based on an external // 32kHz reference clock. After each calibration, the values from the // clock system are read ou
2pc
- 这个程序是用来绘制二维光子晶体的带隙图，所用方法是平面波法-This program is used to map of two-dimensional photonic crystal band gap, the plane wave method is used