搜索资源列表
led(1)
- led 工作原理,及led大屏幕系统的工作原理
LED显示屏控制技术实现.doc
- 关键词:256 级灰度;LED 点阵屏;FPGA;电路设计
基于单片机的电动自行车速度与里程表设计
- 内容摘要:本系统由信号预处理电路、单片机at89c2051、系统化led显示模块、串口数据存储电路和系统软件组成。其中信号预处理电路包含信号放大、波形变换和波形整形。
1
- 交通灯程序,供大家分享,我也是初学者,望大家能多多指教-taffic led
shiyan6[1]
- GIP 系列倒立摆系统是固高科技有限公司为全方位满足各类电机拖动和自 动控制课程的教学需要而研制、开发的实验教学平台。GIP 系列的主导产品由 直线运动型、旋转运动型和平面运动型三个子系列组成。 -GIP Series inverted pendulum system is solid all-round high-tech Co., Ltd. to meet the various types of motors for drag and automation curriculum n
LED
- 【实验题目】 LED闪烁发光 【实验目的】 掌握定时器T0或T1的简单用法。 【硬件接法】 P1.1控制LED,低电平点亮。 【实验步骤】 ISP下载开关扳到“00”,用Flash Magic软件下载程序文件“Timer.hex”,运行。 【运行效果】 LED亮200ms,灭800ms,反复循环。
LED
- 利用下图所连接的电路。编写程序使液晶显示器在第一行显示"Welcome To ",第二行显示"DIAN XIN 1 BAN "。-The figure is connected using the circuit. Programming so that the first line LCD display " Welcome To" , the second line shows " DIAN XIN 1 BAN" .
28-LED-Clock-Timer-Circuit-Schema-With-74HCT
- 28 LED Clock Timer Circuit Schema With 74HCT This is a programmable clock timer circuit that uses individual LEDs to indicate hours and minutes. 12 LEDs can be arranged in a circle to represent the 12 hours of a clock face and an additional 12 L
1.LED
- led 单片机 嵌入式 开发 程序 国信长天杯 电子设计大赛-Single chip embedded development program
LED
- 主要功能和技术指标要求: 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz,1Hz和0.5Hz三种不同频率闪动,各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时,要求采用中断方式 -The main features and technical requirements: 1 LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz an
code-led
- code seven leg module bcd_tang (clock, rst, s1, led) input clock, s1, rst output [6:0] led reg [6:0] led reg [3:0] bcd wire [3:0] bcd_next always @(posedge clock or posedge rst) begin if (rst == 1 b1) begin bcd <= 4
1
- 单片机LED显示屏设计电路图的代码部分,使用C++设计,已经过实现。-Microcontroller LED display design schematics code section, use C++ design has been achieved.
Flashing-an-LED
- 点亮P1口的1个LED灯闪烁。该程序是单片机学习中最简单最基础的,通过程序了解如何控制端口的高低电平-An LED light flashes lit P1 port. The program is SCM learning the simplest and most basic program to understand how to control the high and low of the port
akram-lab-micro-1
- led blinking by 89c51 mcu
IO---1-LED-lights-lit-
- 1-IO输出-点亮1个LED灯方法11- IO输出-点亮1个LED灯方法1-The output of the 1-IO- 1 LED lights lit 1-IO output- 1 LED lights lit 1 1-IO output and 1 LED lights lit method 1
TM1629A_V1.1
- TM1629A TM1629A是带键盘扫描接口的LED(发光二极管显示器)驱动控制专用电路,内部集 成有MCU 数字接口、数据锁存器、LED 高压驱动-LED TM1629A TM1629A is with a keyboard scan interface (light-emitting diode display) dedicated drive control circuit, the internal MCU integrated digital interface, data latc
1
- msp430F5529 Toggle P1.0/LED
Ejemplo-C-1
- Software para controlar un led con una entrada en un micro pic usando pic c compiler
1-LEDdeng
- 流水灯试验,利用MCU控制相关的LED灯。从而掌握MCU相关最小系统及IO口的使用。-Water lamp test
1-开发板入门资料
- 简单的led流水灯,刚开始学单片机,真的好难啊,但这是一个好的开始,我会坚持下去的,自己的第一个单片机程序,哈哈哈哈哈哈哈(ledSimple LED water lamp, just started learning microcontroller, it's really hard, but this is a good start. I will stick to it. My first microcontroller program is hahahahahahaha.)