搜索资源列表
3517fb LED
- 它是3517fb LED灯的电源控制。
LED流水灯
- 单片机控制的LED流水灯的C程序
fpga_docu.rar
- CPLD/FPGA 入门文档。国内某知名fpga开发商编写的基础教程,共18篇。从使用fpga如何点亮led灯到VGA到8051内核使用方法。如果您是打算学习cpld/fpga,建议先阅读这些文章再选择采购开发板。,CPLD/FPGA entry documents. FPGA developers a well-known domestic basis for the preparation of curricula, a total of 18. From how to use the FP
PWM
- 利用定时器控制产生占空比可变的 PWM 波 按K1,PWM值增加,则占空比减小,LED 灯渐暗。 按K2,PWM值减小,则占空比增加,LED 灯渐亮。 当PWM值增加到最大值或减小到最小值时,蜂鸣器将报警。-Have a timer to control the use of variable duty cycle PWM wave by K1, PWM values increase, then decrease the duty cycle, LED lights dimmin
rs232
- 用上位机(PC)通过串行调试助手或是自己做的串口操作软件,发送16进制数,控制8个LED灯的各个的亮与灭。 想让哪个灯亮都可以通过发送数据来实现。目标就是用软件控制硬件!达到单片机实时控制第一步: -With the host computer (PC) via serial debugging aids, or make their own operating software serial port, sending 16 hex numbers to control 8 LED l
top
- 实现定时器功能,分别有秒针,分钟,小时,到一天后led灯闪烁一下。-To achieve timer function, respectively, seconds, minutes, hours, to one day look after the led light flashes.
3.-LED
- 编程学习资料 点亮LED灯 再玩出各种花样的基础-Programming learning material lit LED lights and play out all sorts of figure foundation
LED
- 主要功能和技术指标要求: 1. LED灯外接于P0.0端。 2. LED灯分别按2Hz,1Hz和0.5Hz三种不同频率闪动,各持续10s。 3. 在LED灯开始和停止闪烁时蜂鸣器分别鸣响1次。 4. 利用单片机内部定时器定时,要求采用中断方式 -The main features and technical requirements: 1 LED lights external P0.0 end. 2. LED lights press 2Hz flashing 1Hz an
LED-verilog
- 利用verilog语言点亮led灯,基于2410开发板-The use of the verilog language lights led lights, based on the 2410 development board
led
- LED 点阵点亮 对输入时钟进行分频,依次点亮相应的LED 灯-LED 点阵点亮 对输入时钟进行分频,依次点亮相应的LED 灯
proteus-LED
- proteus LED灯闪烁 很简单,很简单的一个程序-proteus LED Flicker So easy,the easy program
LED
- 介绍如何从片内flash中烧写运行程序,led灯控制闪亮-Describes how to run the program from the flash chip programming, led lamp control shiny
CITE-T-ZA-Led
- zigbee芯片CC2530的,led灯变化程序-the zigbee chip CC2530, led lights change program
LED-blinks
- 通过c语言实现LED灯闪烁,实现方式多样-LED blinks c language implementations diverse
Flashing-an-LED
- 点亮P1口的1个LED灯闪烁。该程序是单片机学习中最简单最基础的,通过程序了解如何控制端口的高低电平-An LED light flashes lit P1 port. The program is SCM learning the simplest and most basic program to understand how to control the high and low of the port
LED
- 这是一个led的程序 可以实现led灯的闪耀-this is a led word!
two-LED-lights-flashing
- 点亮两个LED灯-Two LED lights lit
more-LED-lights-flashing
- 点亮多个led灯-more LED lights flashing
04_led_test
- Verilog写的led灯,可用Vivado/ISE仿真平台仿真(Progress is not created by contented people.)
esp8266控制led灯51单片机底层程序
- 无线模块esp8266控制led灯亮灭51单片机底层程序,只有51单片机的程序没有控制app,使用网络调试助手可以实现手机与51单片机通讯,从而达到控制led灯的亮灭,亲测可行(The wireless module esp8266 controls the LED lamp to extinguish the 51 single-chip microcomputer bottom program. Only the 51 MCU program does not control app. Us