搜索资源列表
lle
- 局部线性嵌入法，用于数据降维 .lle.m -- A simple matlab routine to perform LLE. .scurve.m -- Code to run the \"s-curve\" example. .swissroll.m -- Code to run the \"swiss roll\" example.
ruanjianshixi
- lagrange差值，spline一阶差值，spline二阶差值，坐标平移，s曲线拟合，多项式拟合-Hangzhou margin, a spline bands margin spline second margin, coordinate translation, s curve fitting, polynomial fitting
样条曲线的算法C++代码实现
- 样条曲线的算法C++代码实现，包含三个文件spline.cpp/spline.h/spline_prb.cpp，其中sline_prb为测试程序。此库中包含常见的多项式样条、hemitt样条、B样条等八种样条算法。devc++/vc/gcc下均通过,Spline curve algorithm C++ Code, including the three documents spline.cpp/spline.h/spline_prb.cpp, which sline_prb for the te
S Step Motor AC Control.实现S形曲线升降速
- 实现S形曲线升降速，可适用于步进电机、伺服电机控制系统，加速平稳，振动很小,S-shaped curve to achieve take-off and landing speed, could be applied to stepper motor, servo motor control system, speed up the smooth, low vibration
NURBS-curve
- 这是NURBS曲线的绘制程序，在MATLAB-2008a环境下进行编写，包含了几个基函数子程序。可以通过调节控制顶点和点的权重来调节曲面形状。 -This is a NURBS curve drawing program, in the MATLAB-2008a environments prepared, including a number of basis function subprogram. Can be controlled by adjusting the weight o
Doppler
- 低轨卫星LEO通信系统的多普勒频移估计，通过该程序可以画出多普勒频移的S曲线，可以观测处最大的多普勒频移以及变化率-LEO LEO satellite communication system of the Doppler frequency shift is estimated that the program can be drawn through the Doppler shift of the S curve can be observed to be the highest Dopp
simulation
- 设计一个M/M/S/k排队系统模型，用C++进行仿真，计算一个新的服务请求在各个状态k下的阻塞率，绘制出到达率-阻塞率曲线(matlab)，并将理论值与仿真值进行比较。 M/M/S/k模型为服务请求到达间隔时间服从泊松分布、服务时间服从指数分布、系统有S个服务器、系统容量为k（有限个）的排队系统。如果一个服务请求到达排队系统时，系统内已有k个服务请求，那么这个服务请求就会被拒绝（即不为该服务请求安排服务器，也不会将其排入系统队列）。由于系统容量为k，有S个服务器，所以系统队列的长度为k-S
dipole_example
- 用MATLAB对偶极子天线仿真，得出S曲线图-Dipole antenna with MATLAB for simulation, draw S curve
microwave_patch
- 用MATLAB对微带贴片天线进行仿真，出来S曲线图-Using MATLAB simulation of microstrip patch antenna, out of S curve
S-line
- 利用stc系列单片机的pwm功能控制两个直流电机，从而实现小车自动行走s曲线-Stc series microcontroller pwm function control two DC motors, enabling the car automatically walk s curve
S-Curve-speed-control-research
- S形速度控制曲线较之梯形曲线能够带来更小的负载速度超调与调整时间。-failed to translate
s-line-for-fes
- 像散法求s曲线，一般法和差动象散法求fes曲线-Astigmatic method for the s-curve, the general law and the differential curve astigmatic method for fes
S-curve-deceleration-
- 电机S曲线加减速的matlab程序，对实现电机平滑曲线很有帮助-The motor S curve deceleration of the matlab program
S-curve-generation-tool
- 步进电机加减速S曲线生成工具,参数生成工具看你们有没有用罗-Step motor acceleration and deceleration S curve generation tool
BujinMotor-S-Line
- STM32F103为核心控制步进电机实现S曲线加减速与直线加减速，驱动芯片为ULN2003,并用OLED进行显示，再加入了速度曲线的显示。还能实现加减速，正反转，速度保持。曲线数据使用数据表。-STM32F103 as the core control stepper motor S curve acceleration and deceleration and linear acceleration and deceleration, the driver chip ULN2003, and
步进电机S曲线算法
- 实现步进电机S曲线的算法。可用C语言实现，算法用C实现，然后数据可以通过FPGA用DDS处理，输出任意频率和脉冲个数。(Algorithm for realizing S curve of stepping motor. C language can be implemented, the algorithm is implemented with C, and then data can be processed by FPGA using DDS, output arbitrary freq
直线S曲线驱动
- 利用USB1010运动控制卡控制步进电机直线S曲线运动(Using USB1010 motion control card to control the motion of the linear S curve of the stepping motor)
S-Curve-VC++
- S曲线加减速VC++源程序； 1.运动控制相关的源代码； 2.S型曲线加速； 3.编程语言： VC++；(S curve plus or deceleration VC++ source program; 1. source code related to motion control; 2.S curve acceleration; 3. programming language: VC++;)
源代码
- 七段s曲线路径规划程序详解 非常适合做运动控制规划(Detailed solution of seven segment s curve path planning program)
trajectorygeneration
- 双S曲线轨迹规划，可用于两点之间最短时间规划，并且可以约束速度和加速度最大值(Hyperbolic S-curve trajectory planning, which can be used for the shortest time planning between two points, and can constrain the maximum speed and acceleration)