搜索资源列表
PIC-clock
- 本作品采用Atmel公司的AT89C51单片机,以汇编语言为程序设计的基础,设计一个用四位数码管显示时、分的时钟。在实物图中,左边靠近电源的绿色发光二极管(长亮)是电源指示灯,表示的是5V稳定电源工作正常;单片机左下角红色发光二极管是秒灯,每闪烁一次表示时间走动一秒钟;按键正上方绿色发光二极管是设置灯,当时间正常走动时此时不亮,当第一次按下设置键(右键)时,此绿灯亮,同时秒时熄灭,且分钟的两位数码管出现闪烁,时间停止走动,进入校时状态,表示此时可以进行分钟的调整,当按一次加一键(左键)可实现分钟
freq
- 智能频率计 1. 频率测量范围为1Hz~1MHz 2. 当频率在1KHz以下时采用测周方法 其它情 况采用测频方法.二者之间自动转换 3. 测量结果显示在数码管上,单位可以是Hz(H)、 KHz(AH)或MHz(BH)。 4. 测量过程不显示数据,待测量结果结束后,直接显示结果。 -Intelligent frequency meter 1. Frequency measurement range of 1Hz ~ 1MHz 2. When th
seg_key
- 51单片机按键控制数码管显示程序,显示为时钟倒计时,有暂停和计数功能-51 single-chip digital tube display key control procedures, shown as the countdown clock, a pause, and count functions
dianzizhong
- 定时器0中断, 用于数码管的动态扫描 定时器1中断, 用于产生0.01s的时钟-Timer 0 interrupt, for digital control of dynamic scanning timer 1 interrupt, used to generate clock 0.01s
LedCtrlUse
- 实现浮点数的LED显示,模拟七段数码管显示数字及小数点,里面还包含数字键输入功能.-The realization of floating-point numbers of the LED display, analog Seven-Segment LED display figures and the decimal point, which also includes a numeric keypad input capabilities.
scan_led
- 一个8位数码管扫描程序,经过编译和仿真.-An 8-bit digital tube scanner, after the compiler and simulation.
shumaguan
- 关于51单片机开发板的数码管显示程序 本人菜鸟 望大家多多指教-51 MCU development board on the digital tube display program I hope everyone rookie exhibitions
stc232
- 1.通过PC端的串口调试工具,从PC端发出一个十六进制的数, 通过串口传输到单片机,并有单片机通过LED数码管显示其ASII码,而且单片机又将这个数发回PC端,并在PC端显示出来,从而实现单片机与PC机的通讯 2.可以实现对下位机数据实时采集(如温度,程序中设定的是37摄氏度) 3.可以控制流水灯或继电器开关等-1. Through the PC-side debugging tools for serial port, from the PC client sends a hexa
dongtai
- 这是一个数码管动态显示的C语言程序.适合初学单片机朋友参考使用.-This is a dynamic display of digital tube C language program. Singlechip friends for beginner use and reference.
dongtai1
- 这是另一个数码管动态显示的C语言程序.请有兴趣的朋友参考参考.-This is another dynamic display of digital tube C language program. Interested parties are invited to refer to refer to a friend.
clock
- set(key6) left(key5) right(key4) up(key3) down(key2) OK(key1) 功能一:时钟 时钟计时; 按下set(一次)键即可调时间,此时时钟计时停止,按left,right左右移动点,移动到需调的的数码管, 按up,down进行数字的调节,按OK键保存退出。 功能二:整点报时和闹钟 当时钟走到整时时,报时滴滴响四次; 按set(二次)键进入调节闹钟,此时时钟继续走动,按left,rig
DS18B20
- 温度传感器18B20程序,本设计硬件简单,用4位数码管显示-Temperature sensor 18B20 procedure, the design of the hardware is simple, with four digital tube display
18B20
- DS18B20温度控制数码管 1、K3 → 进入设定温度报警值 TL 状态:L--20 2、K3 → 进入设定温度报警值 TH 状态:H--28 3、K3 → 返回-DS18B20 temperature control digital tube 1, K3 → to enter the set temperature alarm value TL state: L- 20 2, K3 → to enter the set temperature alarm value TH stat
paobiao2
- 000-999跑表 STC89C52单片机 + 数码管显示-000-999 stopwatch STC89C52 Singlechip+ Digital tube display
chuankoufasonghejeishou
- C51串口中断接收和发送程序,采用数码管显示串口发送过来的代码,只能显示发送的数字代码-C51 serial port receive and transmit interrupt procedures, the use of digital tube display serial port to send over the code, can only display the numeric code to send
MyClock
- 自定义像数码管一样的数字时钟控件-Customize the same as digital tube digital clock control
ww
- ds18b20的温度显示程序,显示到数码管,并可以进行温度报警的上限设置-DS18B20 temperature display program, indicating that the digital tube, and can set the upper limit of temperature alarm
a
- 0-999计数器 单片机数码管显示-0-999 counter Singlechip digital tube display
PIC
- 多位数码管动态扫描显示的方法。 //六位数码管从左到右显示0123456六位数字。-A number of digital tube display dynamic scan method.// 6 digital tube from left to right shows a six-figure 0,123,456.
DigitClock2
- 本工程通过vc++6.0实现了数码管的显示 可以显示漂亮的数字时钟显示-This works through vc++ 6.0 to achieve a digital tube display can show beautiful digital clock display