搜索资源列表
LED
- AVR单片机源代码,采集按键值,并点亮LED.
1-IO输出-点亮1个LED灯方法1
- 1-IO输出-点亮1个LED灯方法1
旋转LED
- 二、 要求 1. 基本要求 (1) 制作一个由16只 LED构成的线状点阵及其控制电路,安装于可旋转的平台上,利用红外遥控实现LED显示功能的切换,电机带动平台以合适速度旋转。 (2) 开机时装置完成显示自检,能对点阵中16只LED逐个点亮,每只LED显示时间约为1秒,此时平台不旋转。 (3) 平台开始旋转后,通过无线方式切换,实现16个同心圆图形分别顺序(由大到小)和逆序(由小到大)显示,每个同心圆图形显示时间为1秒左右。 (4) LED显示亮度能依据环境亮度变化自动调节。 2. 发挥部分 (
fpga_docu.rar
- CPLD/FPGA 入门文档。国内某知名fpga开发商编写的基础教程,共18篇。从使用fpga如何点亮led灯到VGA到8051内核使用方法。如果您是打算学习cpld/fpga,建议先阅读这些文章再选择采购开发板。,CPLD/FPGA entry documents. FPGA developers a well-known domestic basis for the preparation of curricula, a total of 18. From how to use the FP
light--LED.rar
- 点亮LED灯,C语言编写,可以在keil下运行。实现第一个小灯的不停闪烁,初学着可以好好参考。,LED lights lit, C language, you can run keil. Achieve the first of a small non-stop flashing lights, can make reference to the beginner.
LED-PWM.rar
- led渐变功能.渐变点亮然后渐变暗,led渐变功能.渐变点亮然后渐变暗,a gradual change
LED
- 点亮一个LED灯,PIC单片机学习,Proteus-To light a LED lamp, PIC Singlechip learning, Proteus
LED
- TMS320F28335点亮LED的程序,采用时基中断,调试成功运行-TMS320F28335 lit LED process, using time base interrupt, debug, run successfully ~ ~ ~ ~
LED
- s3c2410开发平台上实现的点亮LED的代码MAIN部分-S3C2410 development platform to achieve the lit LED code MAIN part
s3c2410-double-led
- 基于ARM,s3c2410的led显示程序,可实现8位数码管的显示,可控制任意数码管点亮与关灭。-Based on the ARM, s3c2410 the display program led to the realization of an 8-bit digital tube display, can be controlled with any clearance digital tube lights out.
led
- 自己用89C51编辑的一个小程序,可以控制256个二极管循环点亮,proteus仿真过了-Own use 89C51 editing a small program that can control the light cycle of 256 diodes, proteus simulation after a
4-IO输出-点亮多个LED灯方法2
- 4-IO输出-点亮多个LED灯方法2(4-IO output - lighting multiple LED lights method 2)
3 位操作点亮多个LED
- 初学者入门,单片机简单的用位操作点亮多个led(Bit operation lights up multiple LED)
01 闪烁的LED
- 简单单片机的小实验-----让led闪烁起来(Simple microcontroller small experiment -- let LED flashing up)
Design01
- 点亮led是所有软硬件测试中最基本的项目,本程序用CYPRESS的Psoccreator开发环境实现软硬件的联调,点亮基板上的LED三色灯(Lighting LED is the most basic item in all software and hardware testing. This program uses CYPRESS's Psoccreator development environment to realize the joint adjustment of softwar
2.LED
- 点亮LED的小程序,控制STM32。用C语言编写(Control STM32 to light LED by VC++.)
01.点亮三个发光二极管(LED)
- LED点亮三个发光二极管复位按键控制单片机(LED lighting three light-emitting diode reset buttons to control singlechip)
11
- 基于C语言与MSP430F5529实现8个LED循环点亮(8-LED cycle light based on C language and MSP430F5529)
【实验01】点亮一个发光二极管方式1
- 点亮第一个LED灯,开启单片机学习之旅,你一定会觉得它很有用的(Light the LED light Lighting the first LED light and opening the learning journey of MCU, you will find it very useful.)
4.1.1:nrf52832-LED
- 操作gpio引脚点亮LED,学习简单的操作nrf52832芯片的gpio引脚。(Operate GPIO pin to light LED, learn simple operation of nrf52832 chip GPIO pin.)