搜索资源列表
ALIENTEK-MINISTM32--led-
- ALIENTEK MINISTM32 实验1 跑马灯，为初学者提供点亮LED灯的模板-ALIENTEK MINISTM32 Experiment 1 Marquee
led
- 8个发光二极管D1~D8分别接在单片机P1.0-P1.7端口上，一个开关接在P3.0上。 要求输出端口输出“0”时，发光二极管亮。 开关闭合时，开始按P0.0+P0.7、P0.1+P0.6、P0.2+P0.5、P0.3+P0.4的顺序依次点亮LED，再按P0.3+P0.4、P0.2+P0.5、P0.1+P0.6、P0.0+P0.7的顺序点亮LED，重复循环。开关断开时，立刻停止点亮指示灯。 开关断开时，立刻停止点亮指示灯。 -Eight light-emitting diodes
Item-two-LED-cycle-light
- 循环点亮LED灯，实现每隔几秒钟轮流点亮，简单实用，可以自己动手做做，还配有电路图-Cycle lit LED lights, to achieve every few seconds turn light, simple and practical, you can do it yourself, but also with a circuit diagram
LED
- STM8S003F3 DEMO例程，点亮LED 灯，无外部晶振，最小例程，基于IAR 编译器。-STM8S003F3 DEMO u4F8B u7A0B uFF0C u70B9 u4EAHR09 u708F uFF0C u65E0 u5916 u90E8 u6676 u632F uFF0C u6700 u5C0F u4F8B u7A0B uFF0C u57FA u4E8EIAR u7F16 u8BD1 u5668 u3002
main
- 根据STM32寄存器地址，配置P0~P3为推挽输出，点亮LED灯。(According to the STM32 register address, the configuration P0~P3 is push-pull output, and the LED lamp is lit.)
5.接收短信控制LED灯
- 1、板子上电后运行指示灯RUNING_LED会以一秒的频率闪烁； 2、通过芯片的串口1可以监视模块的登录情况； 3、手机发送“onled”点亮LED； 4、手机发送“offled”熄灭LED； 5、使用串口2与模块通信，串口1用于将信息打印输出。(1, after the board power, the operating indicator RUNING_LED will flicker at a frequency of one second; 2, through the ch
LED
- LED跑马灯，多个LED灯轮流点亮熄灭,遍历后从头开始，不停止(LEDs are on or off in certain order)
实验1：LED闪烁
- 1.STM32 GPIO管脚配置 2.点亮发光二极管(1.STM32 GPIO pin configuration 2. Light the light emitting diode)
mcu_led2
- 基于vivado平台，使用microblaze搭建一个小系统，并能点亮led(Based on the vivado platform, the use of MicroBlaze to build a small system, and can light LED)
2048
- 16X16LED灯矩阵不同方式点亮，实现动态循环点亮(The 16X16LED lamp matrix is lighted in different ways to realize dynamic cycle lighting)
1-IO输出-点亮1个LED灯方法1
- IO口输出点亮一个LED IO口可配置 51单片机(The LMH6401 is a very high-performance, differential I/O, digitally-controlled variable gain amplifier (DVGA))
实验1 跑马灯实验
- 点亮LEd 跑马灯，正常开始LED灯，正常发出红黄蓝三种颜色(Light LED Happy lights, normal start LED lights, the normal issue of red and yellow blue three colors)
user_first_fpga_20170620
- 程序可实验开发板上LED循环点亮，且可通过按键控制流动速度，用到了PLL IP 和 计数器模块。(Program with LED flashing circuit uses PLL IP and counter. And extinction rate is controled by key.)
点亮第一个led灯
- 点亮第一个LED,我是一名高三毕业生，九月份大学才开学，我报了电子专业，想在暑假把单片机先自学了，希望能在这里找到些帮助。(Light the first led light.)
2-LED
- 点亮LED，翻转电平，入门例程，IO口操作(Lit LED, flip level, beginner routines, IO operations)
01.LED点灯实验_STM32F407
- 用STM32F407 实现基本的点亮LED，刚接触STM32F407的同学可以参考(Ligth LED on STM32F407)
lpc2109
- 利用IO口点亮LED 通过按键可以控制LED闪烁(Using IO port lit LED, you can control the LED flashing through the button)
LED
- 点亮led 不使用其他平台说给的定义引脚方法(Lighting LED does not use other platforms to define the pin method)
LED
- LED驱动应用程序 点亮关闭led(open LED close LED)
点亮一个LED灯
- 用51单片机点亮一个LED灯，简单的程序。·(With 51 singlechip lighting a LED light, a simple procedure.)