搜索资源列表
MicroCell
- 12V供电 铅蓄电池充电模块（充电电流200-400mA）原理图及PCB图，附带指示灯，充满保护，器件清单。-12V rechargeable lead-acid battery power supply module (charge current 200-400mA) and PCB schematic diagram, with light, full protection, the device list.
c8051f300chongdian
- 基于c8051f300设计的锂电池充电器的应用笔记。内有源代码和原理图-C8051f300 design of lithium-based battery charger application notes. Within the source code and schematic
chongdian
- 用matlab/simulink搭建的铅酸蓄电池充电模型。-Using matlab/simulink model to build the lead-acid battery charging.
BatteryStatus.tar
- 电池充电量显示界面，可以用于工业监控界面程序的开发，欢迎大家使用-Battery capacity display interface, the interface can be used for industrial monitoring program development, welcome to use
BatMonitor
- 通过程序读取系统电池状态信息，包括容量，充电充满需要多少时间，放电还可以放多久-Read through the procedures for the system battery status information, including the capacity, how much time required full charge, discharge can also take time
ch
- 采用飞利浦P89LPC916制作的锂离子电池充电器的C源代码,请参考.-Philips P89LPC916 produced using lithium-ion battery charger C source code, please refer to.
cs0301
- 智能电池充电电池管理芯片CS0301.内容非常全。可以给一般理电池和非理电池。-Intelligent battery charging battery management chip CS0301. Very wide. Can give a general rationale for the battery cell and non-justification.
51_single-chip_based_on_th_realization_of_lead-aci
- 在蓄电池应用领域, 铅酸蓄电池以可靠、电容量大、维护简单等特点占有很大的市场。本文太阳能铅酸蓄电 池的充电方案采用了在单片机领域应用最广的51 单片机, 依靠adc 进行模拟量数据采集并在51 上采用软件实现pwm 算法 对12v 铅酸蓄电池进行( 三段精细) 充电控制, 得到良好的控制效果。基于51 单片机的铅酸蓄电池充电器的实现-Applications in batteries, lead-acid battery to a reliable, large capacity, si
N10_TestBattery0
- 工厂产线测试电池软件，VC编写，用来测电池状态，充电百分比，电流大小及温度！-code testing the battery of the notebook computer
NickelCadmiumandNickelHydrideBatteryChargingApplic
- HT48R062 在镍氢、镍镉电池充电器中的应用-Nickel Cadmium and Nickel Hydride Battery Charging Applications Using the HT48R062
ni-mhcharge
- 镍氢电池详细的充电方法以及C代码,不错的文章.-Ni-MH battery charging methods and the detailed C code, a good article.
main
- PIC10f220 完成的电池充电保护 -PIC10f220 complete battery charging protection
Ni-mH_battery_charger
- 镍氢电池充电器方案，含汇编程序，来自ATMEL-Ni-mH battery charger solution, include assembly firmware
batterycharge
- 通过单片机程序控制对电池分时充电，并通过热敏电阻实时测温，防止电池充电过程过度发热-MCU programmed by time-charging the battery and, through the thermistor temperature measurement, battery charging process to prevent over-heating
EUP8054ver1.0
- 单节锂电池充电芯片手册 EUP8054 PDF文件-EUP8054 datasheet
CodeCharger
- 共享我自制的充电器程序，此程序可以控制我的四节电池充电， 内部算法适用于小容量的锂电池充电-I share my home-made charger program, this program can control my four batteries, the internal algorithm is suitable for small-capacity rechargeable lithium battery
595643732051
- 充电程序，充满后转为涓流充电，每月分钟表对电池检测一次。
code
- 主要用于单节锂离子电池充电控制，采用美信半导体公司得锂电池充电芯片，其工作原理如下：有电池插入时，LED亮，蜂鸣器发出提示音，系统进入充电。-Mainly used for single cell Li-ion battery charge control, the use of Maxim Semiconductor chips have lithium batteries, it works as follows: a battery inserted, LED light, buzzer
Second
- 使用在锂电池充电器上的材料，包括采集等信号处理-Lithium battery charger used in the material, including the collection of signal processing, etc.
android电池管理
- BatteryService作为电池及充电相关的服务： 监听Uevent、读取sysfs里中的状态、广播 Intent.ACTION_BATTERY_CHANGED(BatteryService Uevent sysfs Intent.ACTION_BATTERY_CHANGED)