搜索资源列表
chongdianqi
- STM32103VCT6单片机作为主控制器，实现对手机电池的充电，充电过程分为涓流，恒流，恒压等。-STM32103VCT6 MCU as the main controller, to achieve the cell phone battery, the charging process is divided into trickle, constant current, constant voltage and the like.
taiyangneng
- 实现太阳能电池板稳定输出5v电压，并实现充电给3.7v锂电池-To achieve stable output of solar panels 5v voltage, and to achieve charging
Protocol-between-Charger-and-BMS
- GBT 27930-2015《电动汽车非车载传导式充电机与电池管理系统之间的通信协议》-GBT 27930-2015 u300A u7535 u52A8 u6C7D u8F66 u975E u8F66 u8F7D u4F20 u5BFC u5F0F u5135 u7535 u673A u4350 u7C60 u7BA1 u7C6 u7CFB u7EF U7684 u901A u4FE1 u534F u8BAE u300B
rh-charge
- 可以实现对蓄电池的恒流充电与切换。对于电池保护很有效果-Can achieve the battery constant current charging and switching, for the battery protection is very effective.
657
- 基于51单片机的太阳能风能路灯控制器设计,本系统采用STC89C52单片机+太阳能电池板电路+风机电路+充电保护电路+升压电路+锂电池电路+电源电路设计而成。-Based on the 51 single-chip solar wind energy street lamp controller design, the system uses STC89C52 single-chip+ solar panel circuit+ fan circuit+ charge protection cir
bts
- 电池测试仪，主要用于检测过电流、电压、容量、内阻、充电、放电温度、电池循环寿命，并给出曲线图。(Battery tester, mainly used to detect over-current, voltage, capacity, internal resistance, charging, discharge temperature, battery cycle life, and gives the curve.)
TB5021
- PCBA具有充电过充保护，放电过放保护功能；电池电量低于3.2时闪烁，3.0V时停机;当电压过低时,为了保护电池不被过度放电,本体会自动禁止运行。(fgashasjsdfjfdksfjsdhadjajajadfhadfhadhadhadhah)
MainBoard_SmipleV_20151218
- 一个太阳能智能灯的控制电路，自带红外红外热释传感器，5-12V太阳能输入，带充电电池管理，AVR单片机。(A control circuit for the solar energy lamp, with its own infrared infrared thermoluminescence sensor, 5-12V solar input, charge battery management, AVR microcontroller.)
GB／T 27930-2015
- GB/T 27930-2015电动汽车非车载传导式充电机与电池管理系统之间的通信协议(Communication protocol between non vehicle conductive charger and battery management system of GB/T 27930-2015 electric vehicle)
PTC-SERIES
- 串联式混合动力电动汽车的能量控制策略，恒温控制策略，当电池SOC在合适范围内依靠电机驱动，发动机关闭与否取决于汽车行驶所需要的能量。低于SOC下限时，依靠发动机驱动，多余能量为蓄电池充电。高于上限时关闭发动机依靠电机驱动。((Series Hybrid Electric Vehicle Control Strategy of energy, constant temperature control strategy, when the battery SOC at the right to re
bq25703a
- 这是具有系统功率监控器和处理器热量监控器的bq25703A I2C 多化合物电池降压/升压充电控制器(bq25703A I2C Multi-Chemistry Battery Buck-Boost Charge Controller With System Power Monitor and Processor Hot Monitor datasheet)
vc_001
- 1.SOC，全称是State of Charge，荷电状态，也叫剩余电量，代表的是电池使用一段时间或长期搁置不用后的剩余容量与其完全充电状态的容量的比值，常用百分数表示。(1.SOC, full name is State of Charge, state of charge, also called residual power, represents the ratio of the remaining capacity of the battery after it has been us
dcdc
- 光伏发电DC-DC 仿真，利用H 桥型双向 DC/DC 变换器的原理 其电压极性不变，但电流的极性却不同，因此能够实现能量的双向流动，功率可以向两个方向流动，而能量流动的方向可由负载大小以及光伏电池的发电特性而决定。对于储能装置的电路拓扑结构，本文采用 H 桥型 Buck/Boost 直流变换器来完成对蓄电池充电放电的控制。(DC-DC simulation of photovoltaic power generation)
锂电池BOOST 充电电路程序IAR格式
- STM8S103寄存器版本BOOST升压电路程序，亲测可用，包含按键和数码管显示以及PWM和ADC采集！(STM8S103 register version BOOST step-up circuit program, pro test available, including buttons and digital display, as well as PWM and ADC acquisition!)
Simscape_PEV_Heat_dissipation
- 本代码分析了插电式混合动力汽车充电时电流等参数对电池热量的影响，以及对充电参数的优化(This code analyses the influence of charging current and other parameters on battery heat of plug-in hybrid electric vehicle, as well as the optimization of charging parameters)
GB_decode
- C代码编程，gcc编译，PC上运行。遵循《GB/T 27930-2015 电动汽车非车载传导式充电机与电池管理系统之间的通讯协议》，根据协议将截取到的CAN报文（一般是csv格式）解析成相应的文本，方便直观的排查故障。(C code programming, GCC compilation, running on PC. Following the "Communication Protocol between GB/T 27930-2015 Electric Vehicle Non-
1.3kw72test
- 充电机程序,超威电池72V，六段式充电。(charge program Charger Procedure Charger Procedure, Superwei Battery 72V, Six-stage Charging.)
HEV_p
- 串联式混合动力电动汽车的能量控制策略，恒温控制策略，当电池SOC在合适范围内依靠电机驱动，发动机关闭与否取决于汽车行驶所需要的能量。低于SOC下限时，依靠发动机驱动，多余能量为蓄电池充电。高于上限时关闭发动机依靠电机驱动。(I am very sorry ,my english very poor)