搜索资源列表
juchibo
- 用计数器原理来实现递增锯齿波和递减锯齿波的程序设计-The principle used to achieve incremental counter and descending sawtooth sawtooth programming
jietifangbo
- 用计数器来完成阶梯拨程序设计以及方波的程序设计-With counters to complete the ladder as well as the allocation of programming procedures square design
sanjiaobo
- 利用计数器来实现三角波的程序设计任务,用于信号发生器-Use counters to achieve the triangular wave of program design tasks, for the signal generator
juchib0
- 用计数器来实现递增锯齿波以及递减锯齿波的程序设计-Using counters to achieve incremental and descending sawtooth sawtooth Programming
s5_counter
- xilinx3s400开发板厂家光盘源码。计数器conuter-CD-ROM manufacturers xilinx3s400 source development board. Counter conuter
CNT10
- 这是十进制计数器的源程序,有需要的同学可以参照一下!-This is the decimal counter source, needy students can refer to you!
CNT10_P
- 这是消除毛刺十进制计数器的源程序,有需要的同学可以参照一下!-This is counter to eliminate glitches decimal source, needy students can refer to you!
CNT10_T
- 这是同步十进制计数器的源程序,有需要的同学可以参照一下!-This is a source synchronous decimal counter, needy students can refer to you!
cnt24_t
- 这是二十四进制计数器的源程序,有需要的同学可以参照一下!-This is 24 hexadecimal counter source, needy students can refer to you!
cntm60
- 这是六十进制计数器的源程序,有需要的同学可以参照一下!-This is a six decimal counter source, needy students can refer to you!
p5
- 内部定时器实验 在使用8051的定时器/计数器前,应对它进行编程初始化。对于不同的方式,定时器的最大定时间隔,计数器的满计数值不同。本实验中8051单片机的时钟频率为6MHz,在P1.7端接有一个发光二极管,-Experiments in the use of an internal timer 8051 timer/counter before it is programmed to respond to initialize. For different ways, the greate
clock
- Holtek单片机源码:此应用示范了使用HT48C10单片机的 16 位定时计数器产生内部中断以实现计时功能。这个应用依靠系统时钟频率作为计时的基准。此处所示的应用使用了 400KHz的系统时钟,通过内部除四分频产生 100KHz 的定时/计数器时钟。对于一个 16 位的计数器最大计数值为 65536,这将每隔 0.65536 秒产生一个内部中断。但是时钟需要1秒作为基本时间单元。 因此定时/计数器被设置成记录0.5秒的基准时间,取两次中断可得到 1 秒的基准时间。这里的应用使用 4 个 7 段
cnt_100
- 带有同步复位的可加载的100制进的可加可减计数器-With synchronous reset can be loaded into the 100 system can be increased or decreased Counter
34
- 1.求两个数的最大公约数 2. n! 3. 循环计数器 4.堆栈 5.实现大数的加减运算-1. The common denominator for both the number of 2. N! 3. Loop counter 4. Stack 5. The realization of addition and subtraction of large numbers of computing
SCHK
- 实验图1是一含计数使能、异步复位和计数值并行预置功能4位加法计数器,例1是其VHDL描述。由实验图1所示,图中间是4位锁存器;rst是异步清信号,高电平有效;clk是锁存信号;-Figure 1 is a test with count enable, asynchronous reset and preset features include numerical parallel adder four counters, Example 1 is described in VHDL. By e
shifter
- 完成一个加速器设计,全加器,具 8位计数器-Complete a accelerator design, full adder, an 8-bit counter
kn_cnt256
- 此程序实现的是可逆计数器,通过对外部引脚的设置,何种进制。 -Realization of this process is reversible counter, through the external pin settings, what kind of band.
HW
- 红外在单片机上的应用,C语言源码,Keil uVision3工程文件,附原理图及说明学习文档 红外接收电路采用集成红外接收器成品H1,接收器包括红外接收管和信号处理IC,均集成在红外接收器H1内。接收器对外只有3个引脚:Vcc、GND和一个脉冲信号输出PO。Vcc接系统的电源正极(+5V),GND接系统的地线,脉冲信号输出接CPU的中断输入引脚INT0。如果没有红外遥控信号到来,接收器的输出端口PO保持高电平,当接收到红外遥控信号时,接收器件信号转换成脉冲序列加到CPU的中断输入引脚。CPU
testdes
- 是des的一种算法,被称为计数器模式(counter mode)-Is a des algorithm, known as the Counter mode (counter mode)
jsq
- 一个简单的计数器,希望和广大程序员多学习,多沟通-A simple counter, and the vast majority of programmers want to learn more communication