搜索资源列表
环路检测器C51程序
- 环路检测器主要用于车辆检测及金属探测系统,这段小程序采用动态参数修*,纠正了以往固定参数法因积累误差导致的灵敏度随运行时间而降低,甚至死机的情况,此段程序已运行在设备中从未出现异常。
开关电源环路增益测试
- 开关电源环路增益测试.pdf
genzong 提供直扩系统的跟踪环路的matlab程序
- 提供直扩系统的跟踪环路的matlab程序,并对其误差进行分析-Direct expansion system to provide tracking loop matlab program, and its error analysis
gps_tracking
- 澳大利亚新南威尔士大学研究的GPS接收机的FPGA跟踪模块的.v程序,包括载波跟踪环路、码跟踪环路、通道累加等模块。-The University of New South Wales, Australia, the study of the FPGA tracking GPS receiver module. V procedures, including the carrier tracking loop, code tracking loop, the channel accumulati
Ring
- 电网规划中搜索环路的程序,通过给定的网络拓扑结构,判定该网络是否连通,如果连通,判定是否有回路,如果有回路,返回组成改回路的线路集合.-Search network planning process loop through a given network topology, determine whether the connectivity of the network, if connected, to determine whether there is any loop, if loo
dxz
- 低相噪、低杂波数字锁相环路滤波器的设计,caj格式,下载前请安装相应阅读器-Low phase noise, low-noise digital phase-locked loop filter design, caj format, download the pre-install the corresponding reader
costas
- 用costas环实现载波同步。假设发送信号载波频率为3.563Mhz,本地初始频率为3.5628Mhz。程序中直接给出了环路滤波器的参数C1,C2。-this is synchoronization on time recovery basing on matlab
AFC
- 频率偏差估计由信道参数估计和频率偏差估计两部分组成 环路滤波器设计-Frequency offset is estimated by the channel parameter estimation and frequency offset is estimated that two-part loop filter design
Gardner_baseband
- 对基带数字通信的位同步过程进行了仿真,采用Gardner算法,没有用插值。符号用SRRC进行脉冲成形,环路滤波器没有用PI回路,是简单的alfa,1-alfa低通滤波,NCO调整也比较简单。-Baseband digital communications for the bit synchronization process of the simulation, using Gardner algorithm, did not use interpolation. Carried out wit
Low-phase-noise
- 能够完成低相噪、低杂波数字锁相环路滤波器-Low phase noise, low clutter digital phase-locked loop filter design
LOOPFLITER
- 环路滤波器,课程设计作品,经验证可用,强烈推荐下载-LOOPF LITER for communications,great
为你解密单相光伏并网逆变器的环路控制
- PDF资料,详细介绍了单相光伏逆变器的环路控制原理。(PDF data, the loop control principle of single-phase photovoltaic inverter is introduced in detail.)
控制环路设计
- 该文档详细讲解了开关电源控制环路的设计及补偿方法(The document explains the circuit design of the switching power supply in detail)
ON-bright开关电源环路设计与计算
- 该文档详细的分析了开关电源中环路设计的概念及设计方法(In this document, the concept and design method of loop design in switching power supply are analyzed in detail)
二型补偿
- 该资料为开关电源环路补偿中的二阶补偿器传递函数的mathcad推导公式(The data is the Mathcad formula for the transfer function of the two order compensator in the compensation of the switching power supply loop.)
利用dsPIC DSC和DCDT设计模拟和数字电源补偿器
- 利用dsPIC DSC和DCDT设计模拟和数字电源补偿器,简化数字环路设计。(DsPIC DSC and DCDT are used to design analog and digital power compensators to simplify the digital loop design.)
锁相环的matlab环路仿真
- 该模型可以用于计算二阶三阶和四阶锁相环的环路参数,并且能够根据环路参数进行环路稳定性和带宽的仿真。
捕获环路算法
- 卫星接收机捕获环路算法,用于卫星接收机定位捕获跟踪(Satellite receiver capture loop algorithm for satellite receiver positioning capture tracking)
环路滤波器设计
- 具有以下两种作用的低通滤波器:在鉴相器的输出端衰减高频误差分量,以提高抗干扰性能;在环路跳出锁定状态时,提高环路以短期存储,并迅速恢复信号。 环路滤波器一般是线性电路,由线性元件电阻,电容及运算放大器组成。环路滤波器用于衰减由输入信号噪声引起的快速变化的相位误差和平滑相位检测器泄露的高频分量,即滤波,以便在其输出端对原始信号进行精确的估计,环路滤波的阶数和噪声带宽决定了环路滤波器对信号的动态响应。
基于UC3842的反激式开关电源的控制环路设计
- 该资料为基于UC3842的反激式开关电源的控制环路设计(The data is a control loop design of flyback switching power supply based on UC3842.)