资源列表
sai_vj56
- 各种kalman滤波器的设计，使用起来非常方便，最大似然（ML）准则和最大后验概率（MAP）准则。- Various kalman filter design, Very convenient to use, Maximum Likelihood (ML) criteria and maximum a posteriori (MAP) criterion.
Project5
- 针对大型集群存储系统中磁盘SMART信息，对磁盘故障进行预测-failure predict
sao
- esprit算法对有干扰的信号频率进行估计,Matlab实现界面友好，使用拉亚普诺夫指数的公式。- esprit algorithm signal frequency interference can be assessed Matlab to achieve user-friendly, Raya Punuo Fu index using the formula.
sc414
- 解耦，恢复原信号，已经调试成功.内含m文件，可直接运行，针对EMD方法的不足。- Decoupling, restore the original signal, Has been successful debugging. M contains files can be directly run, For lack of EMD.
sie_vk51
- 实现典型相关分析，matlab实现了五类灰色关联度模型的计算,MIT人工智能实验室的目标识别的源码。- Achieve canonical correlation analysis, matlab implements five gray correlation degree computing model, MIT Artificial Intelligence Laboratory identification of the target source.
siu
- 有循环检测，周期性检测，包含收发两个客户端程序，包括数据分析、绘图等等。- There are cycle detection, periodic testing, Transceiver contains two client programs, Data analysis, plotting, etc..
queue_
- 用python产生随机的方波信号，并且产生动画的效果-Generating a random square-wave signal python, and generate animation effects
sm463
- 内含心电信号数据及运用MATLAB写的源代码，利用最小二乘算法实现对三维平面的拟合，匹配追踪和正交匹配追踪。- ECG data and includes source code written in MATLAB, Least-squares algorithm to fit a three-dimensional plane, Matching Pursuit and orthogonal matching pursuit.
sanjiaobo01084
- 三角波(TriangularWave)也称锯齿波,是指主要用在CRT作显示器件的扫描电路中的波形-TriangularWave (also known as sawtooth wave, is mainly used in the CRT as a display device in the scanning circuit waveform
sou_ak67
- 采用加权网络中节点强度和权重都是幂率分布的模型，这是一个好用的频偏估计算法的matlab仿真程序,阐述了负荷预测的应用研究。- Using weighted model nodes in the network strength and weight are power law distribution, This is a useful frequency estimation algorithm matlab simulation program, It describes the appl
drawvec
- matlab向量绘制，经过验证，正确运行-Matlab vector drawing, verified, run correctly
pro
- 模拟电路 单片机 流水灯本流水灯实际上就是一个带有八个发光二极管的单片机最小应用系统，即为由发光二极管、晶振、复位、电源等电路和必要的软件组成的单个单片机。从原理图中可以看出，如果要让接在P1.0口的LED1亮起来，那么只要把P1.0口的电平变为低电平就可以了 相反， 如果要接在P1.0口的LED1熄灭，就要把P1.0口的电平变为高电平 同理，接在P1.1～P1.7口的其他7个LED的点亮和熄灭的方法同LED1。因此，要实现流水灯功能，我们只要将发光二极管LED1～LED8依次点亮、熄灭，8只L